Instruction/ maintenance manual of the product OFE- 290 Henny Penny
Go to page of 18
Model OFE- 290 3-1. OPERA TING COMPONENTS POWER/PUMP Switch A three way switch with center OFF position; move the switch to the position marked POWER to operate the fryer; move the switch to the posit.
Model OFE- 290 3-1. OPERA TING COMPONENTS (Continued) High Limit This high temperature control senses the temperature of the shortening; if the temperature of the shortening exceeds 450°F (230°C), t.
Model OFE- 290 3-4. SWITCHES AND Refer to image at end of this section. INDICA T ORS Product Selection Buttons Select the number of heads, or product, to be cooked by pressing the button below the men.
Model OFE- 290 EXIT COOL Button After cooking, or filtering the shortening, the temperature automati- cally goes into the Cool Mode, which keeps shortening at a lower temperature; this temperature ext.
Model OFE- 290 3-5. FILLING OR ADDING SHOR TENING The shortening level must always be above the heating elements when the fryer is heating and at the frypot level indicators on the r ear of the frypot (Figur e 3-3). Failur e to follow these instructions could r esult in a fir e and/or damage to the fryer .
Model OFE- 290 3-6. BASIC OPERA TION Follow the procedure below on the initial start-up of the fryer , and each time the fryer is brought from a cold, or shut down condition, back into operation. These are basic, general instructions. Be sure to follow KFC’ s Standards Library when operating the fryer .
Model OFE- 290 3-6. BASIC OPERA TION 4. Allow fryer to heat until digital display shows “DROP”. (Continued) (Press the EXIT COOL button if the display shows COOL”) The heat cycles on and off approximately 10 degrees before the setpoint temperature, to help prevent overshooting the setpoint temperature.
Model OFE- 290 3-7. CARE OF THE SHOR TENING FOLLOW THE INSTRUCTIONS BELOW T O A VOID SHOR TENING OVERFLOWING THE FR YPOT , WHICH COULD RESUL T IN SERIOUS BURNS, PERSONAL INJURY , FIRE, AND/OR PROPERTY DAMAGE. 1. T o protect the shortening when the fryer is not in immediate use, the fryer should be put into the Cool Mode.
Model OFE- 290 3-8. FIL TERING INSTRUCTIONS (continued) ONL Y FIL TER WHEN “COOL” IS DISPLA YED. FAILURE T O DO SO CAN RESUL T IN SHOR TENING OVERFLOWING THE FR YPOT , CAUSING SERIOUS BURNS, PERSONAL INJUR Y , FIRE,AND/OR PROPER TY DAMAGE .
Model OFE- 290 3-8. FIL TERING 5. Scrape cracklings and crackling ring from frypot and discard. INSTRUCTIONS Do not let cracklings drain into filter drain pan. These crack- (Continued) lings can cause a burned taste in gravy . W ipe all surfaces with a clean damp towel.
Model OFE- 290 3-10. CLEANING THE FR YPOT After the initial installation of the fryer , as well as before every change of shortening, the frypot should be thoroughly cleaned as follows: 1 . T urn the POWER/PUMP switch to OFF positioin, and unplug unit from wall receptacle.
Model OFE- 290 3-1 1. FIL TER PUMP MOT OR The filter pump motor is equipped with a manual reset button, PROTECTOR-MANUAL located on the rear of the motor , in case the motor overheats. If RESET motor won’t run, wait about 5 minutes before attempting to reset this protective device to allow motor to cool.
Model OFE- 290 3-14. PROGRAMMING 1. Press and hold the FUNCTION button for two seconds. “REG PROGRAM” shows in the display , followed by “CODE”.
Model OFE- 290 7. After the load compensation, press and release the FUNC- TION button. “PROP” and “CONTROL” shows on the left side of the display and the factory preset proportional control temperature shows on the right side of the display .
Model OFE- 290 3-14. PROGRAMMING (continued) 13 . After the end-of-cycle point is set, press and release the FUNCTION button. “HEAD” flashes on the left side of the display and a number shows on the right side of the display .
Model OFE- 290 3-15. SPECIAL PROGRAM MODE (Continued) Factory Presets (F/C, Gas/Electric, Speaker V olume, Speaker Fr equency , Codes, Initialize System) 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display .
Model OFE- 290 3-15. SPECIAL PROGRAM MODE (Continued) T ech I/O Mode 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 4 times until “TECH I-O” shows in the display .
Model OFE- 290 3-16. SPECIAL PROGRAM Heat Control MODE (Continued) 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 6 times until “HEA T CNTRL” shows in the display .
An important point after buying a device Henny Penny OFE- 290 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny OFE- 290 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny OFE- 290 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny OFE- 290 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny OFE- 290 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny OFE- 290, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny OFE- 290.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny OFE- 290. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny OFE- 290 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
