Instruction/ maintenance manual of the product 8000 Henny Penny
Go to page of 11
Model 8000 Computron 1-1. INTRODUCTION This section provides basic operating procedures for the Henny Penny Computron 8000 Fryer. See the Operator’s Manual for the fryer for more details on fryer operation.
Model 8000 Computron 1-3. OPERATING CONTROLS Refer to Figure 1-1. Fig. Item Description Function No. No. 1-1 1 Lights when the control calls for heat; the elements or burners come on and heat the shor.
Model 8000 Computron 1-3. OPERATING CONTROLS (Continued) Fig. Item Description Function No. No. 1-1 9 Press to access program modes; once in the program mode, it is used to advance to the next setting.
Model 8000 Computron Figure 1-1. Control Panel 1-4 103.
Model 8000 Computron 1-4. CLOCK SET Upon initial start-up, or PC board replacement, if “CLOCK SET” automatically appears in the display, start with step 4. 1. Press and hold for 5 seconds until “LEVEL 2” shows in display. 2. Press and “CLOCK SET”, “ENTER CODE” shows in display.
Model 8000 Computron 1-4. CLOCK SET 14. Press and “CS-6, CLOCK MODE” shows in the (Continued ) display, along with “1.AM/PM”. “1.AM/PM” is 12 hour time, “2.24-HR” is 24 hour time. Press to change. 15. Press and “CS-7, DAYLIGHT SAVINGS ADJ” shows in the display, along with “2.
Model 8000 Computron 1-5. BASIC OPERATIONS These are just basic procedures. Refer to the fryer Operator’s AND PROCEDURES Manual for more detailed instructions. 1. Be sure the drain valve is in the closed position. 2. Remove fry basket from frypot and leave lid up.
Model 8000 Computron 1-5. BASIC OPERATIONS 6. Completely stir shortening to stabilize the temperature AND PROCEDURES throughout the frypot. (Continued) 7. Once the shortening temperature has stabilized at the setpoint temperature, place the baskets into the shortening.
Model 8000 Computron 1-5. BASIC OPERATIONS 12. Within a few minutes, the pressure gauge increases to AND PROCEDURES the OPERATING ZONE. If not, recheck the install- (Continued) ation and operation procedures in Operator’s Manual.
Model 8000 Computron 1-5. BASIC OPERATIONS 18. At the end of the Hold Mode, a tone sounds, the AND PROCEDURES display flashes “QUALITY”, and the product it was (Continued) timing. Press and release . In the Cook Mode, when “FILTER SUGGESTED”, shows in the display, the operator has the option to filter at this time, or to continue cooking.
Model 8000 Computron 1-6. CLEAN-OUT MODE ( Continued) NEVER PRESSURIZE FRYER TO CLEAN. LEAVE THE LID OPEN. WATER UNDER PRESSURE IS SUPER HEATED AND CAUSES SEVERE BURNS IF IT COMES IN CONTACT WITH SKIN.
An important point after buying a device Henny Penny 8000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny 8000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny 8000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny 8000 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny 8000 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny 8000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny 8000.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny 8000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny 8000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
