Instruction/ maintenance manual of the product 291 Henny Penny
Go to page of 10
Model 291 1-1. INTRODUCTION This section provides troubleshooting information in the form of an easy to read table. If a problem occurs during the first operation of a new fryer , recheck the installation per the Installation Section of this manual. Before troubleshooting, always recheck the operation pro- cedures per Section 3 of this manual.
Model 291 1-3. TROUBLESHOOTING T o isolate a malfunction, proceed as follows: 1. Clearly define the problem (or symptom) and when it occurs. 2. Locate the problem in the T roubleshooting table. 3. Review all possible causes. Then, one-at-a-time work through the list of corrections until the problem is solved.
Model 291 Problem Cause Correction COOKING SECTION Product color not correct: A. T oo dark • T emperature too high • Check temperature setting in the program mode; see Programming Section in Opera.
Model 291 Problem Cause Correction COOKING SECTION (Continued) D. Spotted • Improper separation of the • Load product into racks product product properly • Breading not uniform on • Sift bread.
Model 291 Problem Cause Correction COOKING SECTION (Continued) D. Rancid taste • Shortening too old • Replace shortening, and follow recommended care and use of shortening • Infrequent filtering.
Model 291 Problem Cause Correction POWER SECTION W ith switch in • Open circuit • Check to see that unit is POWER position, plugged in the fryer is com- • Check the breaker or fuse pletely inope.
Model 291 Problem Cause Correction HEA TING OF SHOR TENING SECTION (Continued) Heating of shortening • Low or improper voltage • Use a meter and check the too slow receptacle against data plate .
Model 291 Problem Cause Correction SHOR TENING FOAMING/DRAINING SECTION Foaming or boiling • W ater in shortening • At end of a Cook Cycle, over of shortening drain shortening and clean frypot; ad.
Model 291 1-4. ERROR CODE T ABLE In the event of a control system failure, the digital display shows an error message. These messages are coded: “E4”, “E5”, “E6”, “E10”, “E15”, “E41”, “E46”, “E47”, “E48”, “E70B” and “E92”.
Model 291 1-4. ERROR CODE T ABLE (Continued) DISPLA Y CAUSE P ANEL BOARD CORRECTION “E-41”, “E-46” Programming T urn switch to OFF , then back to ON, if display shows any Failure o f the error.
An important point after buying a device Henny Penny 291 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny 291 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny 291 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny 291 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny 291 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny 291, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny 291.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny 291. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny 291 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
