Instruction/ maintenance manual of the product CB4842IR Heatiator
Go to page of 40
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 1 Model(s): CB4236IR CB4842IR B-V ent Gas Appliance Owner ’ s Manual Installation and Operation DO NOT DISCARD THIS MANUAL NOTICE • Leave this manual with party responsible for use and operation.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: _______________.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 3 Safety Alert Key: • Indicates a hazardous situation which, if not avoided will result in death or serious injury . • Indicates a hazardous situation which, if not avoided could result in death or serious injury .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 4 = Contains updated information. 15 T roubleshooting A. Intellire Ignition System 3 2 16 Reference Materials A. Appliance Dimension Diagram 34 B. Service Parts List 3 5 C. Optional Components 3 8 D.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 5 B. W arranty 4021-645B 04-02-09 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 6 B. W arranty (continued) 4021-645B 04-02-09 Page 2 of 2 W ARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 7 B. T empered Glass Specications Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as dened by the Consumer Product Safety Commission (CPSC).
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 8 Grate (not shown) Section 14.H. Mantel Section 5.D. Hearth (not required) Clear Space Section 2.D. W all Switch for Fan Section 12.F . Outside Air Kit (behind panel) Section 9.A. Fixed Glass Assembly Section14.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 9 Clear Space 3 ft (0.91 m) in front of appliance D. Clear Space .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 10 J. Lighting Instructions (IPI) • For normal use, activate/deactivate your replace with the wall switch or remote control. • The IPI system may be operated with two D-cell batteries.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 1 1 Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the replace off and allow it to completely cool. • Remove xed glass assembly .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 12 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed: Protective gloves, gla ss cl eaner , drop c loth and a st able wor k sur face.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 13 Burner Ignition and Operation Frequency: Annually By: Qualied Service T echnician T ools needed: Protec tive glov es, vacuum c leane r , whisk broo m, ashli ght, voltmeter , indexed dr ill bit set, and a manom - eter .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 14 Noncombustible roof flashing maintains minimum clearance around pipe Ceiling Firestop on floor of attic Listed B-V ent Pipe Framing.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 15 B. Design and Installation Considerations Heatilator B-type vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 16 Recommended Location Marginal Location Location Not Recommended Recommended Location Multi-level Roofs Windward Leeward Location Not Recommended Figure 4.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 17 A A A C E B B 1/2 in. (13 mm) C 48 in. (1219 mm) max. Drywall D A B C D E in. 42 50-5/8 23-1/2 44 71-5/8 mm 1,067 1286 597 1 118 18 19 in. 48 55-1/4 23-1/2 50 78-1/4 mm 1,219 1403 597 1 270 19 88 Model # CB4236IR CB4842IR 5 F raming and C learances A.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 18 0 in. C B A Note: All pipe clearance specifications are per vent manufacturer's installation instructions. 0 (Clearance to Standoffs) 30 in. (762 mm) clearance to ceiling 1/2 in.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 19 1 in. (25 mm) min. to perpendicular wall A 3-1/2 in. (89 mm) min. from fireplace opening to perpendicular wall B Mantel Leg or Perp.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 20 A. V ent T ermination Minimum Clearances Gas, Wood or Fuel Oil T ermination Cap B Gas T ermination Cap ** A * * If using decorative cap cover(s), this distance m ay need to be increased.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 21 Minimum clearances are per vent manufacturer's specifications Metal plumber's strap secured to framing V ent supports are per vent manufacturer's specifications 12 ft (3.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 22 A. Pipe Clearances to Combustibles V ent clearances are per vent manufacturer ’s specica - tions. The vent MUST be Listed B-V ent pipe. space clearance to vent.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 23 The diagram shows how to properly position, level, and secure the appliance (see Figure 9.2). Nailing tabs are provided to secure the appliance to the framing members. • Bend out nailing tabs on each side.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 24 T abs 1 0 Installing V ent P ip e A. Assembly of V ent Sections This B-V ent appliance requires 5 in. B-vent double-wall pipe. Follow the pipe manufacturer ’s installation guide- lines when installing the unit.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 25 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technicia n using H earth & H ome T e chnologies specied and approved parts.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 26 B. Intellire Ignition System Wiring • Wire the appliance junction box to 1 10 V AC for proper operation of the appliance.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 27 F . W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan, see Figure 12.3: • The power supply for t he appli ance mu st be b rought into a switch box.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 28 Measured from top of hood (in inches) 3 4 5 6 7 8 9 10 1 1 12 13 14 15 16 17 18 5 5-1/2 6-1/4 7 7-3/4 8-1/2 9-1/4 10 10-3/4 1 1-1/2 12-1/4 13 13-3/4 14-1/2 15-1/4 16 30 in. minimum to ceiling 1 in.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 29 A. Remove Glass Assembly See Section J. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the rebox or underneath in the control cavity .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 30 Latches (both bottom and top) Glass Assembly Figure 14.8 Fixed Glass Assembly H. Install the Log Assembly • Base logs ha ve b een p erman entl y mou nted on the gra te assembly and should not be moved.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 31 M. Air Shutter Setting Air shutter settings should be adjusted by a qualied installer at the time of installation. The air shutter is set at the factory for minimum vertical vent run.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 32 1 5 T roubleshoo ting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 33 Sym pt om Possi bl e Cau se Cor re c ti ve Act i on 1 . Pilot won’t light. T he ignitor/mo dule makes noise, but n o spar k.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 34 1 6 Re ference Mater ials A. Appliance Dimension Diagram D i me ns io n s ar e ac t u a l ap pl ia n ce di me ns i o n s. U se f o r r ef er en c e o nl y. Fo r f ra min g dim en sio ns an d cle ar anc es re fe r t o Se cti on 5.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 35 B. Service Parts List Service Parts 06/09 Service Parts Diagram Part number list on following page.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 36 Service Parts 06/09 Service Parts Diagram Part number list on following page. Log Set Assembly Caliber Gas Fireplace 22 21 20 19 10.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 37 Service Parts 06/09 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 38 C. Optional Components Refractory Kit WTBC36DB - For 36 in.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 39 Model # Description FFCM36-B Modernist-style black decorative faux front FFCM36PT Modernist-style pewter decorative faux front FFCM.
Heatilator • Caliber BV Series • 4040-262 • Rev M • 08/09 40 D. Contact Information Please contact your Heatilator dealer with any questions or concerns.
An important point after buying a device Heatiator CB4842IR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Heatiator CB4842IR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Heatiator CB4842IR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Heatiator CB4842IR you will learn all the available features of the product, as well as information on its operation. The information that you get Heatiator CB4842IR will certainly help you make a decision on the purchase.
If you already are a holder of Heatiator CB4842IR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Heatiator CB4842IR.
However, one of the most important roles played by the user manual is to help in solving problems with Heatiator CB4842IR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Heatiator CB4842IR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
