Instruction/ maintenance manual of the product VRT-GY-P-CE Hearth and Home Technologies
Go to page of 44
1 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation.
2 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Rea d this ma nual be fore i nstall ing or ope rati ng this ga s sto ve . Ple ase re tai n this o wner's ma nua l for fut ure r efe rence . Congra tula tion s Congratulations on selecting a Heat & Glo gas stove - an elegant and clean alternative to wood burning stoves.
3 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 - T ABLE OF CONTENTS - Section 1: Listing and Code Approvals A. Gas Stove Certi fi cations ........................... 4 B. Glass Speci fi cations ................................. 4 C. Non-Combustible Materials .
4 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 1 Listing and Code Approvals A. Appliance Certi fi cation B. Glass Speci fi cations This gas stove is equipped with 5mm ceramic glass behind the curved glass. Replace glass only with 5mm ceramic glass.
5 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 2 Getting Started Check building codes prior to installation. • Installation MUST comply with local, regional, state and national codes and regulations.
6 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 3 Appliance Location and Clearances A. Selecting Appliance Location NOTE: · Illustrations re fl ect typical installations and are FOR DESIGN PURPOSES ONL Y . · Illustrations/diagrams are not drawn to scale.
7 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Fire Risk. Odor Risk. T ipping Risk • Install gas stove on a stable, level platform/ fl oor strong enough to support gas stove without tipping. • USE wood fl ooring, ceramic tile, brick hearth or high pressure laminate fl ooring applied directly over the sub- fl ooring material.
8 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 4 T ermination Locations A. Flue T ermination Minimum Clearances Figure 4.2 Multiple V ertical T ermination Figure 4.1 T ermination Clearances Figure 4.3 speci fi es minimum fl ue heights for various pitched roofs.
9 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 4.4 Minimum Clearances for T ermination A = 31 cm .................... clearances above grade, ver anda, porch, deck or balcony B = 31 cm .
10 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 5 Flue Information A. Flue Components B. Use of Elbows These models are approved to use Simpson Dura-V ent or Hearth & Home T echnologies series pipes, components and termination. Approved components are labeled for identi fi ca- tion.
11 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Figure 5.2 Figure 5.3 V H D. Flueing Diagrams STRAIGHT UP VERTICAL FLUE V 1 1.8M Maximum STRAIGHT OUT HORIZONT AL FLUE H 61cm Maximum For Natural, Propane and Butane Gases. For Natural, Propane and Butane Gases.
12 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Figure 5.4 Figure 5.5 V H H V Natural Gas • One 90 0 Elbow System V Minimum H Maximum 46 cm 1.3 M 92 cm 2.7 M 1.4 M 4.1 M 1.8 M 5.0 M V+H = Max 1 1.6 M H Max = 5.0 M Propane • One 90 0 Elbow System V Minimum H Maximum 46 cm 92 cm 92 cm 1.
13 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Figure 5.6 Figure 5.7 V H2 H1 H2 V H1 Natural Gas • T wo 90 0 Elbows System V Min. H1 Max. H1 + H2 Max. 46 cm 55 cm 1.1 M 92 cm 1.1 M 2.3 M 1.4 M 1.7 M 3.5 M 1.8 M 2.2 M 4.5 M V+H1+H2 = Max 10M H1 Max = 2.
14 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Figure 5.8 H2 H1 V V 2 H V1 Figure 5.9 Natural Gas • T wo 90 0 Elbows System V1 Min. H Max. 31 cm 93 cm 61 cm 1.8 M 91 cm 2.7 M 1.2 M 3.6 M 1.5 M 4.5 M V1+V2+H = Max 1 1.4M H Max = 4.5M Propane • T wo 90 0 Elbows System V1 Min.
15 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Figure 5.10 Figure 5.1 1 V 2 H2 H1 V1 V2 H2 V1 H1 Natural Gas • Three 90 0 Elbows System V1 Min. H1 Max. H1 + H2 Max. 46 cm 55 cm 1.0 M 92 cm 1.1 M 2.0 M 1.4 M 1.7 M 3.0 M 1.8 M 2.2 M 3.9 M V1+V2+H1+H2=Max 1 1M H1 Max=2.
16 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 90 DEGREE ELBOW PIPE LENGTH PIPE LENGTH WALL THIMBLE COVER WALL THIMBLE TERMINA TION CAP Step 1. Determine the desired location of the gas stove. Check to ensure that wall studs or roof rafters are not in the way when the flue system is being planned.
17 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 BEFORE YOU BEGIN: Review the fl ueing con fi gurations in Figures A, B and C on the next page . F. Slim Line W all Thimble 1. Assembling Slim Line T rim Ring and Heat Shield 2. Installing Slim Line T rim Ring and Heat Shield Figure 5.
18 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 FIG. A 90 DEGREE ELBOW FIG. B MINIMUM CLEARANCE C ENTER LINE TRIM RING HEA T SHIELD OVER TOP HALF OF PIPE INTERIOR W ALL 51mm clearance fro.
19 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 FL ASHI NG SUPPORT BOX STORM COLLAR VERTICAL TERMINA TION CAP PIPE LENGTH FIRESTOP 1 1.8M MAXIMUM On vertical terminations use only Part #SLK-991DA Figure 5.20 Step 1. Check the installation instructions for required 2.
20 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Step 4. Assemble the desired lengths of pipe and elbows necessary to reach from the gas stove up through the round support box. Ensure that all pipe and elbow connections are in their fully twist-locked position.
21 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 MIN. 25.4 cm CLEARANCE NAILS MIN. 25.4 cm CLEARANCE MIN. 25.4 cm CLEARANCE MIN. 25.4 cm CLEARANCE CEILING FIREST OP Figure 5.
22 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 W ARNING W ARNING CHECK FOR GAS LEAKS Fire Risk Explosion Risk Asphyxiation Risk • Check all fi ttings and connections.
23 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 7 Electrical Information Batt er y p ol ar it y mu st be c or r ec t o r m o dul e d am ag e w il l occur . CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
24 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 8 Appliance Setup A. Remove Shipping Materials B. Unbolting Appliance from the Pallet The gas stove is bolted and screwed to the pallet for ship- ping. Use a 1/2 in. socket to remove the bolt in center of bottom plate.
25 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Figure 8.4 The manufacturer recommends securing the lag bolt from the component bag in the center hole in the bottom plate (clearance hole). This bolt will help to prevent tipping for- ward.
26 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 F . Installing the Baf fl e The baf fl e is shipped wrapped, inside the fi rebox. Install the baf fl e with the embedded “T” side up, place it on top of the brackets on the inside of the fi rebox, ensuring back edge of baf fl e makes contact with the back of the fi rebox.
27 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 G. Positioning the Logs Figure 8.13 Place log #1 into the cradle in the burner . Lean the log back towards right corner of firebox. While still breakable, the logs do not become fragile until after the gas stove is burned and they have cured.
28 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 J. Inner Glass Door Assembly Replacement I. Front Door Glass Assembly Installation Figure 8.17 Complete Assembly T urn the gas stove OFF and let it cool down before replacing the inner glass door assembly .
29 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 9 Operating Instructions A. Before Lighting Appliance Read this entire manual prior to using the gas stove. Failure to follow the instructions may result in property damage, bodily injury, or even death.
30 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 B. Lighting the Appliance Electronic Ignition LIGHTING INSTRUCTIONS T O TURN OFF GAS T O APPLIANCE 1.
31 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 C. After Appliance is Lit When you light your gas stove, you may notice that it pro- duces heat which does have an associated odor or smell.
32 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 10 Maintaining and Servicing Appliance Although the frequency of your gas stove servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an gas stove check-up at the beginning of each heating season.
33 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 Inspect Maintenance T asks Doors 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to air fl ow . 3. V erify maintenance of proper clearance to combustible household objects.
34 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 11 T roubleshooting With proper installation, operation and maintenance your gas stove will provide years of trouble-free service.
35 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 12 Reference Materials A B G F H E Hearth Pad D C I A. Appliance Dimension Diagram Dimensions are actual gas stove dimensions. Use for reference only . For clearances to combustibles refer to Section 3.
36 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 G F A B C D E Hearth Pad B. Appliance Dimension with Stone Surround Diagram Figure 12.2 Appliance Dimensions with Stone Surround Height includes 9.53 mm hearth pad. ABCDE F G Centimeters 75.
37 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 C. Flue Components Diagram Figure 12.3 SL D-Series Balance Flue Component Speci fi cations 10.2 cm inner pipe, 16.8 cm outer pipe. 23.5 cm 16.5 cm 16.8 cm 43.2-61.0 cm 29.8 cm 14.6 cm 16.8 cm 16.
38 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 D. Flue Components List COMPONENTS Ceiling Support / W all Thimble, Black 656-230 Cathedral Ceiling Support, Black 941 15 cm Pipe Length, B.
39 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 11 Service Parts Diagram Service Parts Part number list on following page.
40 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 IMPORT ANT THIS IS DA TED INFORMA TION: When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
41 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 IMPORT ANT THIS IS DA TED INFORMA TION: When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
42 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 V alve Assembly Parts List Service Parts VRTIKL-CE Beginning Manufacturing Date: June 2006 Ending Manufacturing Date: Active IMPORT ANT THIS IS DA TED INFORMA TION: When Requesting service or replacement parts for your appliance please provide model number and serial number .
43 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 F . W arranty Policy HEA T & GLO LIMITED 10 YEAR W ARRANTY In order to presumptively establish the dates to which your HEA T & GLO .
44 Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07 G. Contact Information Heat & Glo, a brand of Hearth & Home T echnologies, Inc. 20802 Kensington Boulevard Lakeville, MN 55044, USA Please contact your Heat & Glo dealer with any questions or concerns.
An important point after buying a device Hearth and Home Technologies VRT-GY-P-CE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hearth and Home Technologies VRT-GY-P-CE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hearth and Home Technologies VRT-GY-P-CE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hearth and Home Technologies VRT-GY-P-CE you will learn all the available features of the product, as well as information on its operation. The information that you get Hearth and Home Technologies VRT-GY-P-CE will certainly help you make a decision on the purchase.
If you already are a holder of Hearth and Home Technologies VRT-GY-P-CE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hearth and Home Technologies VRT-GY-P-CE.
However, one of the most important roles played by the user manual is to help in solving problems with Hearth and Home Technologies VRT-GY-P-CE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hearth and Home Technologies VRT-GY-P-CE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
