Instruction/ maintenance manual of the product SMART-BATT-II Hearth and Home Technologies
Go to page of 12
1 Printed in China Copyright 2006, Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 5504 100-909 G 12 /06 SMART -BA TT -II Remote Control Kit s - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostati- cally or manually from the transmitter .
2 RECEIVER WIRING INSTRUCTIONS Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver .
3 Figure 4. Millivolt with Rocker Switch and Receiver Figure 5. Millivolt with 3 Wire If your fireplace is wired like Figure 3 find the leads on back of the switch marked “For use with remote or wall switch only” and take the leads and plug them into wire lead on remote receiver box (see Figure 4).
4 Figure 6. Millivolt with Receiver Figure 7. Intermittent Pilot Ignition (IPI) Wiring Diagram IGNITION MODULE 3 V AC GRN ORG INTE RMITTE NT PIL OT IGNITOR ORG WHT VA LV E PIGGYBACK ON/OFF SWIT CH BRN.
5 Figure 8. Intermittent Pilot Ignition (IPI) Wiring Diagram If your fireplace look like Figure 7 find the leads on the back of switch marked “For use with remote or wall switch only”. T ake the leads and plus them into wire leads on remote receiver box (see Figure 8).
6 Figure 9. If your fireplace looks like Figure 9 remove the 3-wire off the jumper wire by unplugging the spade from jumper wire. Install the jumper wire on the wire as shown see Figure 10. Then install one of the leads from the remote receiver onto the valve and other wire into the lead on the jumper wire.
7 NOTE: The remote receiver houses the microprocessor that responds to commands from the transmitter to control sys- tem operation. It emits one beep when it receives an ON or OFF command manually , but no beep when cycling on and off automatically in THERMO mode.
8 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer . T o program the remote receiver: 1.
9 SE TTIN G BUTTO N Figure 13. Setting Button/Child Proof Lockout Setting 0 F/ 0 C Scale The factory setting for temperature is degrees Fahrenheit ( 0 F).
10 TRANSMITTER SAFETY FEA TURES It is recommended that the TRANSMITTERS always be lo- cated within a 20 foot operating range of the fireplace, pref- erably in the same room in which the fireplace system is located.
11 4. Then press the MODE button on the transmitter to change the system to ON. The spark electrode should begin sparking to ignite the pilot. After the pilot is lit, the main gas valve should open and the main gas flame should ignite. 5. Press the MODE button on the transmitter to OFF .
12 Limited W arranty This REMOTE CONTROL SYSTEM is warranted for 12 months from the date of purchase or installation to the original purchaser to be free from defects in mate- rials and workmanship.
An important point after buying a device Hearth and Home Technologies SMART-BATT-II (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hearth and Home Technologies SMART-BATT-II yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hearth and Home Technologies SMART-BATT-II - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hearth and Home Technologies SMART-BATT-II you will learn all the available features of the product, as well as information on its operation. The information that you get Hearth and Home Technologies SMART-BATT-II will certainly help you make a decision on the purchase.
If you already are a holder of Hearth and Home Technologies SMART-BATT-II, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hearth and Home Technologies SMART-BATT-II.
However, one of the most important roles played by the user manual is to help in solving problems with Hearth and Home Technologies SMART-BATT-II. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hearth and Home Technologies SMART-BATT-II along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
