Instruction/ maintenance manual of the product RCT-MLT-II Hearth and Home Technologies
Go to page of 11
1 Printed in U.S.A. Copyright 2008, Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 100-907F 4/08 RCT -ML T -II Remote Control Kits - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostati- cally or manually from the transmitter .
2 Figure 1 REMOTE RECEIVER Important: The remote receiver should be positioned close to front in right or left corner where ambient temperatures do not exceed 170º F . The remote receiver is powered by 1 10-120V AC. It plugs into a standard polarized duplex receptacle.
3 Figure 4. Figure 5. VARIABLE REGULATOR GAS CONTROL VALVE FLAME CONTROL SOLENOI D KNOB SCREW NUT VARIABLE REGULATOR JAM NUT VARIABLE REGULATOR SOLENOID WASHER WASHER PLUNGER Installing Flame Control Solenoid 1. Remove the screw and knob from the variable regula- tor and discard.
4 The remote receiver has a 3-position slide switch: OFF/ REMOTE/ON (see Figure 6). Figure 6. Remote Receiver TRANSMITTER Important: Before operating remote control, transmit- ter and receiver must have matching security codes. See section ‘Matching Security Codes’.
5 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer . T o program the remote receiver: 1.
6 Figure 8. Setting Button/Child Proof Lockout Setting ºF/ºC Scale The factory setting for temperature is degrees Fahrenheit ( ºF). T o change this setting to degrees Centigrade (ºC): 1. Remove the battery cover on the back of the transmit- ter and locate the “setting button” at the top center of battery compartment (see Figure 8).
7 Adjusting the Flame Height - Operates in ON or THERMO mode This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER. 1. Press and release FLAME button to change fl ame height to HI (see Figure 7, Location #5), (a second fl ame icon appears).
8 6. Advance the SET temperature on the transmitter to a temperature of at least 2º F (1º C) above the ROOM temperature displayed on the LCD screen and the system fl ame will ignite. 7. Set the SET temperature to at least 2º F (1º C) below the room temperature and the system fl ame will extin- guish.
9 Figure 9. Intermittent Pilot Ignition (IPI) Wiring Diagram Figure 10. Standing Pilot Ignition Wiring Diagram TRAN SF ORMER 3V A C PLUG I N R E D BA T TERY P ACK THER MO ST A T WIRE AS SEMBL Y JUMPER.
10 Figure 12. Standing Pilot Ignition Wiring Diagram Figure 1 1. Intermittent Pilot Ignition (IPI) Wiring Diagram BLACK S2 ON OFF ON/OFF SWIT CH WHITE T2 RED T1 THERMO PILE GAS V AL UE BLACK S1 3/16.
11 Figure 14. Remote Control Standing Pilot Ignition Wiring Diagram Figure 13. Remote Control Intermittent Pilot Ignition (IPI) Wiring Diagram Remote Control Wiring Diagrams V ALVE GREEN ORANGE JUMPER.
An important point after buying a device Hearth and Home Technologies RCT-MLT-II (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hearth and Home Technologies RCT-MLT-II yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hearth and Home Technologies RCT-MLT-II - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hearth and Home Technologies RCT-MLT-II you will learn all the available features of the product, as well as information on its operation. The information that you get Hearth and Home Technologies RCT-MLT-II will certainly help you make a decision on the purchase.
If you already are a holder of Hearth and Home Technologies RCT-MLT-II, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hearth and Home Technologies RCT-MLT-II.
However, one of the most important roles played by the user manual is to help in solving problems with Hearth and Home Technologies RCT-MLT-II. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hearth and Home Technologies RCT-MLT-II along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
