Instruction/ maintenance manual of the product BE-36-C Hearth and Home Technologies
Go to page of 37
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 1 - Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. - What to do if you smell gas • Do not try to light any appliance.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or component s MA Y BE USED .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 3 TABLE OF CONTENTS Safety and W arning Information ................................................ 2 Service Parts Lists ...........................................
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 5 (NG , LP) Service Parts List / Liste des pièces de rechange IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 6 (NG , LP) Exploded Part s Diagram (GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturing Date: .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 7 BE-36-C (NG , LP) Exploded Part s Diagram (GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturin.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 8 Appliance Certification The fireplace model discussed in this Installers Guide has been tested to certification standards and listed by the applicable laboratories.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 9 2 Getting St arted Introducing the Hearth & Home T echnologies G as Fireplaces Hearth & Home T echnologie.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 10 Figure 1. Diagram of model BE-36-C HOOD VENT COL LA R S RA TING PLA TES & LABE LS BOTT OM GRILLE COVER ELEC .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 11 3 Inst alling the Fireplace Step 1. Locating the Fireplace The following diagram shows space and clearance require- ments for locating a fireplace within a room. Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Front .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 12 Figure 3. Framing Dimensions for SL D-Series and DVP-Series Pipe A B C D* E * 3 7 ” 3 3 ” 16 1/4” 36 1/2” 24 3/8 Framing should be constructed of 2 X 4 lumber or heavier .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 13 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . Figure 4 .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 14 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . Figure 5 .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 15 Step 3. Inst alling the V ent System A. V ent System Approvals This model has vent starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of starting collars will be used to attach the vent system.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 16 STRAIGHT UP VERTICAL VENTING V (FT .) 45' MAX. Figure 8. Straight up V ertical V enting Use SL D-Series component s only . NOTE: For vertical venting over 20 feet an Extended V ertical Baffle Kit is recommended for improved flame appearance.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 17 Figure 1 1. V enting with One 90° Elbow V (MIN.) H (MAX.) 90 o Elbow on T op 2.5' (863mm) 1' (305mm) 3 ' (914mm) 2' (610mm) 4' (1.22m) 3' (914mm) 6' (1.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 18 V H H + H 1 1' MIN. (305 mm) 2' MAX. (610 mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22 m) 8' MAX. (2.4m) 3' MIN. (914 mm) 6' MAX.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 19 Figure 13. V enting with T wo 90° Elbows BE-36-C V (MIN.) H + H 1 (MAX.) 90 o Elbow on T op 2.5' (863mm) 1' (305mm) 3' (914mm) 2' (610mm) 4' (1.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 20 Figure 14. V enting with Three 90° elbows 1' MIN. (305 mm) 2' MAX. (610mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22m) 8' MAX. (2.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 21 Use SL D-Series components only . BE-36-C H + H 1 (MAX.) 4' (1.22m) 6' (1.86m) 8' (2.48m) 12' (3.72m) 16' (4.8m) 16' (4.8m) Figure 15.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 22 Figure 16. V enting with Four 90° elbows VENTING WITH FOUR (4) 90° ELBOWS NA TURAL AND PROP ANE GAS V (MIN.) H (MAX.) 2' (609mm) 5' (1.52m) V 1 (MIN.) H 1 (MAX.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 23 B. Installing V ent Components After determining which set of starting collars will be used (top or rear), follow venting instructions accordingly .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 24 For V ertical Runs - The vent system must be supported every eight (8) feet (2.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 25 For V ertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 26 C. V ent T ermination SL-Series V enting Only: For Horizont al T erminations - T o attach and secure the termina.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 27 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 26. V ent T ermination Minimum Clearances A = 12" ......................
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 28 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 29 ! Step 4. Positioning, Leveling, and Securing the Fireplace • Place the fireplace into position. • Level the fireplace from side to side and from front to back.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 30 Figure 30. Gas Supply Line Step 6. The Gas Supply Line NOTE: Have the gas supply line installed by a qualified service technician in accordance with all building codes.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 31 Step 8. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 32 Figure 32. Remote Wiring Diagram (IPI) Figure 33. Remote Wiring Diagram (Standing Pilot) ORANGE GREEN V AL VE OR.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 33 Figure 35. Fan Wiring Diagram FAN TEMP ERA TURE SEN SOR SW I TCH SPEED CONTROL (RHEOST A T) JUNC TIO N BOX Figure 34. Intermittent Pilot Ignition (IPI) Wiring Diagram NOTE 1: Ignition module, valve, pilot and wall switch operate on 3 volts.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 34 Step 9. Finishing Figure 36 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 35 Placing the Ember Material Ember material is shipped with this gas fireplace. The bag labeled Glowing Ember (050-721) is standard glowing ember material. T o place the ember material: • Remove the top louver by lifting it up and away from the unit.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 36 Step 1 1. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: Remove all paperwork from underneath the fireplace.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 37 4 Maint aining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fireplace serv.
An important point after buying a device Hearth and Home Technologies BE-36-C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hearth and Home Technologies BE-36-C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hearth and Home Technologies BE-36-C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hearth and Home Technologies BE-36-C you will learn all the available features of the product, as well as information on its operation. The information that you get Hearth and Home Technologies BE-36-C will certainly help you make a decision on the purchase.
If you already are a holder of Hearth and Home Technologies BE-36-C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hearth and Home Technologies BE-36-C.
However, one of the most important roles played by the user manual is to help in solving problems with Hearth and Home Technologies BE-36-C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hearth and Home Technologies BE-36-C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
