Instruction/ maintenance manual of the product 800 Hearth and Home Technologies
Go to page of 20
MODEL 800 NOV A FREEST ANDING PELLET STOVE INST ALLA TION, OPERA TION, AND MAINTENANCE INSTRUCTIONS CONGRA TULA TIONS— Yo u are now the proud owner of one of the finest stoves in the world for your home—the QUADRA- FIRE! Now before installing your stove and building your first fire, record the serial number on the warranty card.
NOTES Page 2.
T ABLE OF CONTENTS Page Safety Label ................................................................................................................... ........................................... 4 Listing and Specifications .........................
SAFETY LABEL (FOUND ON BACK W ALL OF HOPPER) Page 4.
LISTINGS AND SPECIFICA TIONS QUADRA-FIRE 800 NOV A pellet stoves are safety tested and listed with W arnock Hersey International to ASTME 1509 and ULCS627. Also suitable for mobile home installation (see page 11 for details). HEA T INPUT*: 28,000 to 37,500 BTU per hour P AR TICULA TE EMISSIONS PER HOUR: 0.
FLOOR PROTECTION MINIMUM CLEARANCES TO COMBUSTIBLE MA TERIALS The floor protector must be noncombustible material, extending beneath heater and to the front, sides, and rear as indicated below . NOTE: In a corner installation, the floor protection must follow the above clearances.
Page 7.
Page 8.
Page 9.
T OP VENT FLUE ADAPTER INST ALLA TION INSTRUCTIONS 3"-3" ADAPTER #81 1-0450 3"-6" COLLAR #812-2690 1 ) Put a layer of silicone on the 3" (76mm) exhaust outlet. 2 ) Slide the flue adapter onto the rear exhaust outlet. 3 ) Adjust the assembly to a vertical position.
MOBILE HOME INST ALLA TION OUTSIDE AIR KIT FOR 800 NOV A: P ART #81 1-0420 (FLOOR) OR P AR T #81 1-0430 (REAR) 1 An outside air inlet must be provided for the combustion air and be unrestricted while the stove is in use. 2. The stove must be secured to the mobile home by bolting it to the floor (using lag bolts).
OPERA TING INSTRUCTIONS 1. FUEL SIZE AND MA TERIAL Fuel pellets are made from sawdust or wood byproducts. If the source material is hardwood, they will have a higher mineral content, creating a heavier ash. Minerals and other noncombustible materials, such as sand, will turn into glass when heated to the extreme temperatures our firepot reaches.
Page 13.
Page 14 ( N ) COMBUSTION BLOWER ( WHITE ).
1. FIREPOT A. It takes very little time to clean the firepot. W e recommend that you clean the firepot at least once a week. However , if the fuel you are burning has a high dirt content, it will be necessary to clean the firepot more often. Dirty fuel will cause clinkers to form in the firepot.
1. POWER SUPPL Y A. Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity . 2. FUSE A. The fuse is located on the left side, next to the restart button and the indicator light. However , to access the fuse, you must remove the left side panel.
9. THERMOCOUPLE A. The thermocouple is located on top of the firepot inside the ceramic protection tube. Remove the ceramic tube and inspect the thermocouple for deterioration or breakage. B. Check the terminal block screws to see if they are tight and making a good electrical connection (located on the top of the lower junction box).
1. PLUG IN STOVE, NO RESPONSE A. Check the power supply for 120 volts AC. B. Check the fuse in the junction box (7 amp, 120 volt fuse AGC-7). C. Check snap disc #3 (unplug stove before checking). Push reset on snap disc #3. D. Control box (consult your dealer).
8. THERMOST A T WILL NOT ST ART UNIT A. Check the power to the stove. 1. Unplug for 10 seconds and then plug in. The exhaust blower should come on. If it does, go to B. B. The thermostat or the thermostat wiring maybe faulty . 1. Disconnect the thermostat wires from the terminal block located on the back of the stove.
Aladdin Hearth Products, warrants their pellet heating appliances to the original purchaser for the lifetime of the appliance, to be free from defects in material and workmanship. This warranty gives you specific legal rights; you may have other rights which may vary from state to state.
An important point after buying a device Hearth and Home Technologies 800 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hearth and Home Technologies 800 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hearth and Home Technologies 800 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hearth and Home Technologies 800 you will learn all the available features of the product, as well as information on its operation. The information that you get Hearth and Home Technologies 800 will certainly help you make a decision on the purchase.
If you already are a holder of Hearth and Home Technologies 800, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hearth and Home Technologies 800.
However, one of the most important roles played by the user manual is to help in solving problems with Hearth and Home Technologies 800. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hearth and Home Technologies 800 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
