Instruction/ maintenance manual of the product 6000C-LP Hearth and Home Technologies
Go to page of 10
1 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 RCTS-ML T Remote Control Kits -For use with SIT Millivolt V alves only- - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostatically or manually from the transmitter .
2 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 RECEIVER WIRING INSTRUCTIONS Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver .
3 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 Figure 4. Plunger insertion NOTE: All steps required for installation of the fl ame controller MUST be done by a quali fi ed gas service technician.
4 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 Figure 8. REMOTE RECEIVER JAM NUT REGULA TOR TOWER PLUNGER RED ORANGE BLUE Finalizing Remote Installation 1. Turn the main gas knob ON, relight pilot fl ame, and turn fi replace ON.
5 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 REMOTE RECEIVER The remote receiver has a 3-position slide switch: OFF/ REMOTE/ON (see Figure 7). Figure 7. Remote Receiver TRANSMITTER Important: Before operating remote control, transmitter and receiver must have matching security codes.
6 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer .
7 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 SETTING BUTTON Figure 9. Setting Button/Child Proof Lockout Setting ºF/ºC Scale The factory setting for temperature is degrees Fahrenheit ( ºF). T o change this setting to degrees Centigrade (ºC): 1.
8 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 Adjusting the Flame Height - Operates in ON or THERMO mode This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER.
9 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 7. Set the SET temperature to at least 2º F (1º C) below the room temperature and the system fl ame will extin- guish.
10 Hearth & Home T echnologies • RCTS-ML T Instructions • 100-920 Rev . D • 10/10 THERMOST A T WIRE ASSEMBL Y PIEZO WHITE RED VA LV E PILOT THERMOCOUPLE THERMOPILE Figure 10. Standing Pilot Ignition Wiring Diagram Figure 1 1. Standing Pilot Ignition Wiring Diagram with Piggyback Wire Figure 12.
An important point after buying a device Hearth and Home Technologies 6000C-LP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hearth and Home Technologies 6000C-LP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hearth and Home Technologies 6000C-LP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hearth and Home Technologies 6000C-LP you will learn all the available features of the product, as well as information on its operation. The information that you get Hearth and Home Technologies 6000C-LP will certainly help you make a decision on the purchase.
If you already are a holder of Hearth and Home Technologies 6000C-LP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hearth and Home Technologies 6000C-LP.
However, one of the most important roles played by the user manual is to help in solving problems with Hearth and Home Technologies 6000C-LP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hearth and Home Technologies 6000C-LP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
