Instruction/ maintenance manual of the product 447F Hayter Mowers
Go to page of 24
Operator ’ sManual R48 Recycling Mower G008079 Code 446F , 447F Serial No. 310000001 and Up Manual Part No. 1 1 1-3375 Rev A.
This product complies with all relevant European directiv es , for details please see the separate product specic Declaration of Conformity (DOC) sheet.
Safety Improper ly using or maintaining this mo wer can result in injur y . T o reduce the potential for injur y , comply with these safety instructions. This mow er was designed and tested for reasonably safe ser vice; ho wev er, failure to comply with the follo wing instr uctions ma y result in personal injury .
– Do not mow ex cessiv ely steep slopes. – Exercise extreme caution when on slopes . – Mow across the face of slopes , nev er up and down and ex ercise extreme caution when changing direction on slopes . – Alwa ys be sure of your footing on slopes .
Safety and Instructional Decals Important: Safety and instruction decals ar e located near areas of potential danger . Replace damaged decals. Manufacturer ’ s Mark 1. Indicates the blade is identied as a part from the original machine manufacturer .
Setup Unfolding the Handle 1. Unlock the handle locks , mo ve the handle sections into the operating position, and loc k the handle locks (Figure 3). Figure 3 2. Unlock the upper handle locks and rotate the upper handle upw ard and loc k it into a position that is comfortable to you (Figure 4).
Installing the Fuse (Model 447F Only) Y our mow er comes with a 40-amp fuse that protects the electric starter . Important: Y ou cannot start the mo wer with the electric star ter or charge the batter y unless y ou install the fuse. 1. R emov e the batter y cover and the batter y and locate the fuse holder (Figure 7).
Product Overview G01201 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Figure 9 Model 447F shown 1. Lower handle lock 8. Rear door 2. Grass bag 9. Oil ll/Dipstick (not shown) 3. Upper handle lock 10. Fuel tank cap 4. Recoil start handle 1 1. Cutting height lever (2) 5.
detergent oil with an API ser vice classication of SF , SG , SH, SJ , SL, or higher .) 3. Install the dipstick. Adjusting the Cutting Height Adjusting the cutting height may bring you into contact with the mo ving blade, causing serious injur y . • Stop the engine and w ait for all moving par ts to stop.
sides , and the mo wer will automatically keep pace with you. Figure 15 Stopping the Engine 1. R elease the blade control bar (Figure 16). Figure 16 2. When the engine stops , remo ve the ignition key when you lea ve the mo wer . Important: W hen y ou r elease the blade control bar , both the engine and blade should stop within 3 seconds.
G008083 Figure 18 Removing the Grass Bag T o remo ve the bag, rev erse the steps abo ve . Rear-discharging the Clippings Use the rear disc harge for cutting very tall g rass . If the bag is on the mow er , remo ve it (refer to R emo ving the Grass Bag) before rear -discharging the clippings (Figure 19).
– Raise the cutting height on your mow er . – Cut the grass more frequently . – Overlap cutting swaths instead of cutting a full swath with each pass . – Set the cutting height on the front wheels one notch lower than the rear wheels . F or example , set the front wheels at 60 mm and the rear wheels at 70 mm.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the rst 5 hours • Change the engine oil. Before each use or daily • Check the engine oil level. • Ensure that the engine stops within 3 seconds after releasing the blade control bar .
Lubrication Lubricating the Wheel Gears Ser vice Inter v al: Y early—Lubricate the wheel gears . 1. R emov e the wheel bolts on the rear wheels and remov e the rear wheels . 2. Apply a lubricating oil to the gear as sho wn in Figure 21. Figure 21 3.
Figure 23 4. Slowly pour oil into the oil ll tube until the oil level reaches the Full line on the dipstick (Figure 6). Do not o verll. (Max. ll: 0.59 l, type: SAE 30W detergent oil with an API ser vice classication of SF , SG , SH, SJ , SL, or higher .
Drive System Maintenance Adjusting the Self-propel Drive If y our mo wer does not self-propel properly , adjust the self-propel dri ve cable . 1. Loosen the nut on the cable mount (Figure 25). Figure 25 1. Nut on cable mount 2. Pull the upper handle bac k fully rearward (Figure 26).
Blade Maintenance Replacing the Blade Ser vice Inter v al: Every 25 hours—R eplace the blade or hav e it sharpened (more frequently if the edge dulls quic kly).
Cleaning Cleaning the Mower Ser vice Inter v al: Before each use or daily—Clean the mow er . Tipping the mo wer may cause the fuel to leak from the carburetor or the fuel tank. P etrol is extremely amma ble, highly explosiv e, and under cer tain condition can cause personal injur y or proper ty damage.
Notes: 19.
Notes: 20.
1st Y ear (12 months) W e certify that this service has been carried out by an Authorised Hayter Service Dealer Date: 1st Y ear (12 months) Owner’s Name: Serial Number: Date: 2nd Y ear (24 months) W.
.
LIMITED WARRANTY Hayter Limited warrants to the original user/purchaser that this unit shall be free from defect s in material and workmanship under normal use and service for a period of three years from the date of purchase. The manufacturer of major proprietry components ie.
CUS T OME R INFO RMA TI ON Date of Sale:- Y our Local Dealer:- HA Y TER L IM ITED , SPEL L BR OO K, BI SHOP ’S S T O R TF O RD , H E R T S . C M 2 3 4B U, E N G L A N D Code Serial No.
An important point after buying a device Hayter Mowers 447F (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hayter Mowers 447F yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hayter Mowers 447F - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hayter Mowers 447F you will learn all the available features of the product, as well as information on its operation. The information that you get Hayter Mowers 447F will certainly help you make a decision on the purchase.
If you already are a holder of Hayter Mowers 447F, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hayter Mowers 447F.
However, one of the most important roles played by the user manual is to help in solving problems with Hayter Mowers 447F. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hayter Mowers 447F along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
