Instruction/ maintenance manual of the product AL030 Harmar Mobility
Go to page of 16
M OB I LI TY M O B I L I T Y M O B I L I T Y AL010 MICRO SCOOTER LIFT AL030 POWER TOTE MANUAL WHEELCHAIR LIFT INST ALLA TION GUIDE & OWNER'S MANUAL AL010 Micro Scooter Lift AL030 Power T ote for Manual Wheelchairs Congratulations on your new lift purchase.
Section 1 - Unpacking the Lift Your Universal Out side Lift was factory pre-assembled to require little assembly before installation. Box contents should include: AL010 - Micro Scooter Lift LIFT BODY .
Section 2 - Wiring the Vehicle Important Note: IMPROPER WIRING IS THE #1 CAUSE OF PROBLEMS IN THE OPERATION OF A VEHICLE LIFT . FOLLOW THE WIRING INSTRUCTIONS CAREFULLY Located in the hardware package is the vehicle wiring harness. The harness is manufactured to, and complies with the SAE J1128 requirements.
Section 3 - Vehicle Preparation T o install the lift on a vehicle, it must be capable of accepting a hitch. If you are unsure about the hitch required, there are different places for you to check. Hitch Shops - Check your local area for shops that specialize in trailer hitches.
Measure from Hitch Bar to ground 5-13" 13-15" 15-17" 17-19" Section 4 - Installing the Lift ( no Swing A way option ) Your lif t will come shipped to you factory pre-assembled.
Measure from Hitch Bar to ground 5-12" 12-14" 14-16" 16-18" Drawings below depict a Class 3 Hitch Adapter The installation for a Class 2 is identical Move the folded lift to the rear of the vehicle with the motor box folded away from the vehicle.
2 Push bottom of bracket 3 While holding bottom of bracket, rotate handle 4 Finish rotating handle, aligning holes 5 Install safety pin LOCKED NOT LOCKED YES NO NO Section 6 - Operating the Swing Away Option Many scooter and chair owners require access to the rear of a vehicle.
ON DOWN UP "PLA TFORM KEEPER" W EL DE D TO PL A TF O RM Section 7 - Operating the AL010 Micro Scooter Lift Insert Key and switch to "ON" position Press down on T oggle switch momentarily . Once platform has been lowered at least an inch, unfold the platform.
LOADING YOUR SCOOTER ON THE LIFT Turn ON the power switch with the key furnished with your lift. Lower the platform using the UP/DOWN toggle switch. Pushing the switch downward will cause the platform to lower. Unfold the platform, then continue lowering to the ground.
ON DOWN UP "PLA TFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least an inch. WE LD ED TO PLAT FO RM Insert Key and switch to "ON" position Press down on T oggle switch momentarily .
Section 8 - Operating the AL030 Power T ote for Manual Wheelchairs LOADING YOUR WHEELCHAIR ON THE LIFT Turn ON the power switch with the key furnished with your lift. Lower the platform using the UP/DOWN toggle switch. Pushing the switch downward will cause the platform to lower.
Loosen nuts here Slide arm up or down tube Tighten after adjustment Section 9 - Adjusting the AL010 and AL030 N O I S N E T T S U J D A N O I S N E T T S U J D A N O I S N E T T S U J D A N O I S N E .
Section 10 - Safety & Maintenance SAFETY : Caution: Keep hands away from PINCH POINTS. As with most mechanical objects, the hinge point of a moving part creates a pinch point. Be sure to not to stick fingers or extremities at or near these points.
Section 11 T roubleshooting guide The lift does not operate Check the power supply. The wiring harness ( both wires ) must be run directly to the battery . Attaching the black ( ground ) wire to the frame of the vehicle is NOT considered a reliable ground.
ITE M # DESCRIP TIO N PART # 1 SWIT CH PLAT E ALA12055 2 TOGGLE SWITCH ALA12010 3 KEY SWIT CH ALA12015 4 MOTOR COVER ALA12050 5 ACTUATOR ALA10010 6 OUT ER T UBE - AL01 0 ALA0103 7 HOLD DOW N ARM - A L.
16 15 14 + KEYSWITCH ACTUATOR 12V POLE REVERSING SWITCH BATTERY TRAILER PLUG MOTOR COVER LIGHT B R OW N CIRCUIT BREAKER VEHICLE HARNESS ITE M # DESCRI PTI ON PART # 1 SWIT CH PLAT E ALA12055 2 TOGGLE .
An important point after buying a device Harmar Mobility AL030 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harmar Mobility AL030 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harmar Mobility AL030 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harmar Mobility AL030 you will learn all the available features of the product, as well as information on its operation. The information that you get Harmar Mobility AL030 will certainly help you make a decision on the purchase.
If you already are a holder of Harmar Mobility AL030, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harmar Mobility AL030.
However, one of the most important roles played by the user manual is to help in solving problems with Harmar Mobility AL030. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harmar Mobility AL030 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
