Instruction/ maintenance manual of the product 44836 Harbor Freight Tools
Go to page of 16
ASSEMBL Y AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yright © 2001 by Harbor F reight T ools.
1. KEEP WORK AREA CLEAN AND DR Y . Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN A W A Y FR OM W ORK AREA. Do not allow children to handle this product. 3. ST ORE IDLE EQUIPMENT . When not in use, tools and equipment should be stored in a dr y location to inhibit r ust.
SKU 44836 P A GE 3 5. USE EYE, HEARING, AND BREA THING PRO TECTION. Wear ANSI appro v ed saf ety impact ey e glasses, ANSI appro v ed hearing protection, and ANSI approv ed dust mask or respirator when using this product.
sure this product is always plugged into a grounded 3-hole electrical receptacle with an appropriate breaker switch in-line. 2. MAKE SURE THE POWER SWITCH IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD. 3. DO NO T ABUSE THE PO WER CORD .
SKU 44836 P A GE 5 10. CAUTION: Some woods contain preservatives such as copper chromium arsenate (CCA) which can be toxic. When drilling these materials extra care should be taken to avoid inhalation and minimize skin contact. 11. ALLO W THE DRILL BIT T O SPIN UP T O FULL SPEED BEFORE DRILLING INT O THE WORKPIECE.
SKU 44836 P A GE 6 3. T o attac h the Head Assemb l y (par t #1B) to the Column (par t #1A) , loosen the Hex Screws (part #13B) to ensure the Screws do not protrude internally in the Column (par t #1A), as this would pre v ent the Head Assembly from sliding do wnward fully onto the Column.
Bolts of appropriate length, W ashers and Locknuts (not pro vided). T o Install/Reposition The Drive Belts: 1. The Drill Press features 12 speed selections from which to choose. 2. The two V -Belts (par ts #21C, 26C), when positioned on the three Pulle ys (parts #3C, 28C, 19C), will determine the speed at which the Drill Press will run.
SKU 44836 P A GE 8 T o Obtain The Pr oper Cutting Speeds: 1. Factors which determine the best speed to use in the Drill Press are: A . The kind of material being dr illed. B . The siz e of the hole. C . The quality of cut desired. 2. Generally , in soft mater ial the speed should be higher than f or hard materials.
T o Adjust The T ab le: 1. The T ab le (par t #9A) may be adjusted in 4 directions . 2. T o raise or lower the T ab le , release the T ab le Clamp (par t #11A), and tur n the Crank (par t #6A) clockwise to raise the T able and countercloc kwise to lower the T ab le .
SKU 44836 P A GE 10 5. The Drill Press is now set to drill holes to your pre-determined depth, provided the surf ace of the workpiece is flat and le v el.
SKU 44836 P A GE 11 5. Set the depth of drill bit travel so that the drill bit cannot come into contact with the T ab le (par t #9A), or align the T ab le so that the hole in its center is in line with the drill bit. 6. The Drill Press is now ready to operate.
SKU 44836 P A GE 12 FIGURE G.
SKU 44836 P A GE 13 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PR O VIDED THE P AR TS DIA- GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y .
DESCRIPTION Head w/P ointer & T r im Motor Hex Nut M8 W asher 8 Cord - Motor Hex Nut M10 Lockwasher 10 Bracket - Motor Hex Head Screw M8 x 1.25-20 Support - Motor Bracket Roll Pin 6 x 16 Knob - Motor Adjusting Hex Screw Socket Set M8 x 1.
SKU 44836 P A GE 15 ASSEMBL Y DIA GRAM B NOTE: Some parts are listed and shown for illustra- tion pur poses only , and are not available individually as replace- ment parts.
P AR TS LIST/ASSEMBL Y DIA GRAM C SKU 44836 P A GE 16 NOTE: Some parts are listed and shown for illustration pur poses only , and are not av ailable individually as replacement parts.
An important point after buying a device Harbor Freight Tools 44836 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 44836 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 44836 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 44836 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 44836 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 44836, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 44836.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 44836. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 44836 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
