Instruction/ maintenance manual of the product 42827 Harbor Freight Tools
Go to page of 17
GEARED HEAD DRILL / MILL MACHINE 42827 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 2 SPECIFICA TIONS INCLUDED ACCESSORIES 5 and 6mm Hex W renches Draw Bar R-8/JT2 Chuck 14 / 17mm Open End W rench Slotted Screwdriver Head W rench FEA TURES 1. This machine may be used for surface cutting, drilling, milling, and tapping.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 3 SAFETY W ARNING & CAUTIONS READ ALL INSTRUCTIONS BEFORE USING THIS T OOL! 1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. 2. OBSER VE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 4 14. ST A Y ALER T . W atch what you are doing. Do not operate this machine when you are tired. 15. DO NOT OPERA TE THIS MACHINE WHILE UNDER THE INFLUENCE OF ALCOHOL, DRUGS, OR PRESCRIPTION MEDICINES.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 5 FEA TURES AND CONTROLS OF THE #42827 DRILL / MILL MACHINE 1. Column 2. Head Collar 3. Head Collar Lock Bolt 4. Head Crank 5. Lock Nut 6. Oil Drain Plug 7. T able Feed Wheel 8. T ravel Stop 9.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 6 UNP ACKING AND INST ALLA TION 1. Remove protective crating and skids carefully . In the event of damage in transit, contact Harbor Freight T ools immediately .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 7 BASIC OPERA TION Prior to Operation 1. Check the oil level, and if necessary ll to the mid point of the oil level window . Basic Controls Please r efer to Figur e 1 on page 5. 1.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 8 Preparing for Milling 1. Adjust the positive stop gauge to its uppermost position. 2. Using the spindle feed handle, adjust the bit to approximately the correct height. T ighten the knob in the center of the spindle feed handle (#16).
SKU 42827 For technical questions, please call 1-800-444-3353. Page 9 Installing and Changing T ools W A R N I N G : T urn off t h e p o w e r an d unplug t h e m a c h in e b e f o r e i ns t a l l i n g o r c h a n g i n g t o ol b i t s . Removing Face Mill or Drill Chuck Arbor 1.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 10 Additional Safety Rules for Drilling and Milling 1. Be sure the drill bit or cutting tool is securely locked in the chuck. 2. Be sure the chuck key is removed from the chuck before turning on the power .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 1 1 The spindle bearing is very hot. 1. There is insufcient lubrication. T urn off the power , and check the bearing for lubrication. If necessary , apply a medium weight bearing grease.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 12 NOTICE: 1 10 V olt systems deliver highly energetic curr ents which ar e capable of causing lethal injury . Do not operate this machine without rst obtaining professional installation and safety inspection to pr event operator injury .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 13 PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE P AR TS DIAGRAM IN THIS MANUAL AS A RE.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 14 GEARED HEAD DRILL MILL MACHINE, HEAD P AR TS LIST Please refer to Parts Diagrams on Page 16 and 17 Part Description Qty .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 15 DRILL MILL MACHINE, P ARTS LIST Please refer to Parts Diagrams on Page 16 and 17 REV 09b Part Description Qty .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 16 VER TICAL MILLING MACHINE, HEAD P ARTS DIAGRAM Please refer to Parts List on Pages 14 and 15.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 17 VER TICAL MILLING MACHINE, BASE P ARTS DIAGRAM Please refer to Parts List on Page 15.
An important point after buying a device Harbor Freight Tools 42827 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 42827 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 42827 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 42827 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 42827 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 42827, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 42827.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 42827. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 42827 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
