Instruction/ maintenance manual of the product 36698 Harbor Freight Tools
Go to page of 10
12” SLIP ROLL Model 36698 Assembly & Operating Instructions ® 3491 Mission Oaks Blvd. / Camarillo, CA 9301 1 V isit our Web site at: http://www .
Specifications SA VE THIS MANUAL Y ou will need this manual for the safety instructions, operating instructions, and parts list. Put it in a safe, dry place for future reference. Keep your invoice with this manual. Write the invoice number on the inside front cover .
8. USE EYE AND EAR PROTECTION. Use a full face mask if the work you are doing produces metal filings, dust or wood chips. Goggles are acceptable in other situations. Wear a clean dust mask if the work creates a lot of fine or coarse dust. When operating for extended periods of time, use approved ear protection.
MOUNTING Step 1: Bolt the Slip Roll to a secure work surface using the four holes in the BASE (#25). Step 2: Y ou must purchase your own hardware. Buy four 5/16” bolts, nuts and lock washers, and eight washers. Add 1” to the thickness of your workbench to determine the appropriate length of your bolts.
ADJUSTMENTS 1. T o increase the gap between SHAFT I (#17) and SHAFT II (#18) to allow for varying thickness of materials, screw out the ADJUSTMENT KNOB (#24). T o decrease the gap, screw it in. Make sure to adjust both KNOBS an equal amount. See Figure 1.
OPERA TION Step 1: Perform all adjustments as required (see ADJUSTMENTS section) depending upon material thickness and whether you are engaging in straight rolls or cones. Step 2: Insert material’ s edge between SHAFT I (#17) and SHAFT II (#18). See Figure 3.
Step 5: T o form wires, select the smallest groove that you can use and put the edge of that wire on the groove of SHAFT II. Other operations are identical to sheet metal forming. See Figure 5. Step 6: T o form rings from wire, process the wire until the end meets the length of the stock.
MAINTENANCE Keep rolls free of oil, dirt and grease at all times. Lubricate the gears as necessary by injecting grease through the hole in the OIL CUP (#2).
P ARTS LIST ITEM# DESCRIPTION QTY ITEM# DESCRIPTION QTY 1 Adjustment Screw 1 1 5 Bushing 1 2 Grease Cap 1 1 6 Gear 2 3 Rotating Support 1 1 7 Shaft I 1 4 Adjustment Knob 2 1 8 Shaft II 1 5 L eft Stan .
P ARTS DIAGRAM Page 10 -- SKU 36698.
An important point after buying a device Harbor Freight Tools 36698 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harbor Freight Tools 36698 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harbor Freight Tools 36698 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harbor Freight Tools 36698 you will learn all the available features of the product, as well as information on its operation. The information that you get Harbor Freight Tools 36698 will certainly help you make a decision on the purchase.
If you already are a holder of Harbor Freight Tools 36698, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harbor Freight Tools 36698.
However, one of the most important roles played by the user manual is to help in solving problems with Harbor Freight Tools 36698. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harbor Freight Tools 36698 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
