Instruction/ maintenance manual of the product 32113XX1 Hans Grohe
Go to page of 16
T alis S² 32110XX1 32112XX1 T alis S² 32111XX1 32113XX1 Installation Instructions / W arranty.
2 T echnical Information Recommended water pressure 15 - 72 psi Max. water pressure 116 psi Max. hot water temp. 176 o F* Recommended hot water temp. 120 o F - 140 o F* Flow rate 1.6 gpm Batter y (32210/32212 only) CR-P2 / 6 V Lithium Automatic shutoff after 1 min.
3 Do not install this faucet on a sink with a raised lip. Do not bend or twist the supply hoses! ok! no!.
4 Installation notes • Flush the hot and cold supplies thoroughly before installing the faucet. Damage to the faucet caused by debris is not covered under the warranty . • The hot and cold supplies should be of equal pressure. • The faucet should not be used with a con- tinuous flow water heater .
5 Installation Position the faucet on the sink or countertop (1). Install and tighten the mounting nut (2). T ighten the tensioning screws (3). Connect the 3/8” adapters to the stops (4). Connect the hoses to the adapters (5). T ighten the hoses with two wrenches, as shown, to prevent the hoses from twisting.
6 T emperature adjustment - 32111XX1 / 32113XX1 only T ur n the water supplies off (1). Disconnect the faucet power cable from the batter y pack or AC power pack (2). Remove the screw from the rear of the faucet (3). Connect the faucet power cable to the batter y pack or AC power pack (1).
7 Remove the faucet body (1). T ur n the temperature screw for ward to make the water cooler , backward to make it warmer (2). Dr y any drops of water from the faucet or mounting surface. Replace the faucet body (1). Replace the screw (2). T ur n the water supplies on (3).
8 Battery replacement -- models 32110XX1 / 32111XX1 only If the LED in the sensor window flashes, the batter y is low , but the faucet can still be used. If the LED lights continuously , the batter y must be changed before the faucet can be used. Remove the four screws and the batter y pack cover .
9 Clean the aerator and filters -- all models If the water flow is reduced over time, clean the aerator (a) and the filters (b). T ur n the water supplies off (1). Disconnect the power cable (2). Unscrew the aerator (a) with the ser vice key . Disconnect the hot and cold supply hoses from the adapters.
10 W ait 30 seconds (1). Place a hand in front of the sensor to turn the faucet on (2)..
11 Cleaning The faucet may be turned off temporarily so that the sink may be cleaned. Cover the sensor window with a hand for approximately 10 seconds. The faucet will turn off for approximately 60 seconds, so that the sink may be cleaned. The LED in the sensor window will flash.
12 Reduce the sensor range The sensor is set for maximum range at the factor y . If the faucet is used on a ver y small or highly reflective lavator y , the sensor range may be reduced by ap- proximately 2”. Disconnect the power cable for approximately 10 seconds (1).
13 Replacement Parts 1 aerator 98802XX0 2 fixing set 13961000 3 AC adapter 4 batter y , lithium CR-P2 / 6V 5 batter y box 98801000 6 connection hose 98809000 7 electronics 98803000 8 check valve 96456000 9 aerator ser vice key 98808000 Maintenance note : the check valves (item #8) should be removed and checked yearly .
14 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
15 the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No.
An important point after buying a device Hans Grohe 32113XX1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hans Grohe 32113XX1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hans Grohe 32113XX1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hans Grohe 32113XX1 you will learn all the available features of the product, as well as information on its operation. The information that you get Hans Grohe 32113XX1 will certainly help you make a decision on the purchase.
If you already are a holder of Hans Grohe 32113XX1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hans Grohe 32113XX1.
However, one of the most important roles played by the user manual is to help in solving problems with Hans Grohe 32113XX1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hans Grohe 32113XX1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
