Instruction/ maintenance manual of the product 26017XX1 Hans Grohe
Go to page of 24
Installation Instructions / W arranty Pharo Skyline 26017XX1.
2 Installation Considerations For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber . Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation.
3 Suggested installation Minimum ceiling height -- 86 5/8”.
4 Rough-in Install 1/2” NPT male nipples at the positions shown on the rough-in diagram for the hot and cold water supplies. The nipples should extend 5/8” outside the surface of the finished wall. Install the finished wall surface. Make the wall water tight.
5.
6 Seal the wall around the elbows with waterproof sealant. Failure to seal the wall can lead to possible water damage. Installation W rap the threads on the nipples with T eflon tape. Install the elbows. The elbow outlets should face downward. Drill the holes for the mounting screws with an 8 mm bit.
7 Hang the panel over the top screws only (1). With a partner holding the panel out of the way , Install the panel supply hoses on the elbows. T ighten the hose nuts. (2) Raise the panel (3). Push the bottom of the panel over the bottom screws (4). Lower the panel (5) so that the screws are in the narrow parts of the keyways.
8 T ighten the nuts using a 10 mm wrench. Place a black rubber hose washer in one end of the handshower hose. Install this end of the hose on the handshower outlet. Place the screen washer in the other end of the hose. Connect this end of the hose to the handshower .
9 Reset the HIgh T emperature Limit Stop (Optional -- if required by local code) Remove the thermostatic mixer handle and safety set. Remove the clip and stop ring from the thermostatic mixer stem. T urn the water on to the handshower . T urn the stem until the output water is the desired maximum high temperature -- usually 110°F - 112°F .
10 Justify the handle T urn the water on to the handshower . T urn the ther mostatic mixer handle until the output water is 100�F . T urn the water off. Remove the thermostatic mixer handle and safety set. Reinstall the safety set so that the notch is at the 12:00 position.
11 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No.
User Instructions / W arranty Pharo Skyline 26017XX1.
2 T echnical Information Recommended water pressure 14.7 - 72.5 psi Minimum water pressure 29 psi Max. water pressure 147 psi Recommended hot water temp. 120� - 140� F* Max. hot water temp 165�F* Max. flow rate: showerhead 2.5 gpm handshower 2.5 gpm neck spray 2.
3 User Instructions T urn the top volume control clockwise to obtain water from the overhead shower . T urn the top volume control counter-clockwise to obtain water from the neck spray . It is not possible to run the overhead shower and the neck spray simultaneously .
4 T urn the bottom volume control counter-clockwise to obtain water from the bodysprays. It is not possible to run the handshower and bodysprays simultaneously .
5 Neck spray and handshower • Neck spray and bodysprays • Using the thermostatic mixer T urn the ther mostatic mixer handle clockwise to make the water cooler . T urn it counter-clockwise to make it war mer . The handle will stop at the 100° safety stop.
6 Open the overhead shower and neck spray T o open the overhead shower and neck spray , press the lower left hand corner of the cover . T o open the footrest, press the upper left corner of the cover . The showerhead will open to the 95° position. Push it upward to the 110° position, if desired.
7 Adjust the showerhead cover If the showerhead or neckspray cover does not hang straight, loosen or tighten the set screw with a 3 mm Allen wrench to correct.
8 Cleaning the hand and overhead showers The handshower and overhead shower use the Rubit TM self-cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub over the channels with a finger or a sponge to dislodge them.
9 Replacement Parts 28532XX1 28276XX0 98875XX0 98874XX0 98883000 94082000 94074000 97582000 96509000 97342XX0 98891XX0 98891XX0 97441XX0 94282000 95041000 96519XX1 96483XX0 98879000 98880000 98882001 .
10 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
11 THIS W ARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT P A Y FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 3XX04 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No.
An important point after buying a device Hans Grohe 26017XX1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hans Grohe 26017XX1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hans Grohe 26017XX1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hans Grohe 26017XX1 you will learn all the available features of the product, as well as information on its operation. The information that you get Hans Grohe 26017XX1 will certainly help you make a decision on the purchase.
If you already are a holder of Hans Grohe 26017XX1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hans Grohe 26017XX1.
However, one of the most important roles played by the user manual is to help in solving problems with Hans Grohe 26017XX1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hans Grohe 26017XX1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
