Instruction/ maintenance manual of the product 06633XX0 Hans Grohe
Go to page of 16
Installation Instructions / W arranty Solaris E 06633XX0 Stratos E 06577XX0 Metro E 06653XX0 Swing C 06117XX0 Swing C 06118XX0 Swing C 06119XX0 T ango C 06040XX0 T ango C 06041XX0 T ango C 06042XX0 Li.
2 Installation Considerations For best results, Hansgrohe recommends that this unit be installed by a licensed, profes- sional plumber . Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation.
3 T echnical Information Recommended water pressure 14.7 - 72.5 psi Max. water pressure 147 psi Recommended hot water temp. 120 � - 140 � F* Max. hot water temp 165 � F* Hole size in mounting surface 1 1/4” valves, 1 3/8” spout Max. mounting surface depth 1 1/2” Flow rate 2.
4 Install the handles Swing C, T ango C, Limbo C only: Install the deco-rings on the handles Install the connecting hoses Push a compression nut and ferrule over the end of the connecting hose. Push the end of the hose into the valve outlet. T ighten the compression nut wrench tight.
5 Install the pull rod Solaris E, Stratos E, Metro E, and Swing C only : The pull rod is cur ved. It should be installed with the cur ve as shown in the diagram. T ango C and Limbo C only: The pull rod is straight. All models: Hold the lever in the desired “off” position with one hand.
6 Install the Pop Up Drain Remove the plunger assembly . Unscrew the drain outlet flange from the tee. Unscrew the tailpiece from the tee. W rap the threads with T eflon tape and replace. Install the flexible sealing gasket to the flange. Sit it in the sink outlet.
7 Robinets de lavabo À prendre en considération pour l’installation Pour de meilleurs résultats, Hansgrohe recommande que ce produit soit installé par un plombier professionnel licencié. V euillez lire attentivement ces instructions avant de procéder à l’installation.
8 Données techniques Pression d’eau recommandée 22 -72 psi 22 -72 psi 22 -72 psi T empérature recommandée pour l’eau chaude 120° – 140°F* 120° – 140°F* 120° – 140°F* Dimension du t.
9 Installation des tuyaux de raccordement : Poussez un écrou à compression et une bague d’ex- trémité sur l’extrémité du tuyau de raccordement. Poussez l’extrémité du tuyau dans l’orifice de la valve. Serrez fermement l’écrou à l’aide d’une clé.
10 Installation de la tige d’entraînement Les tiges d’entraînement des robinets T ango C et Limbo C sont droites. Les tiges d’entraînement des robinets E et Swing C sont incur vées. Les tiges doivent être installées tel Les tiges doivent être installées tel Les tiges doivent être installées tel qu’illustré dans le schéma.
11 Installation de l’obturateur à clapet Retirez le plongeur . Dévissez la collerette du raccord en T . Dévissez la queue du raccord en T . Enrobez les filets de ruban de plom- berie Téflon et remettez en place. Installez le joint d’étanchéité sur la colle- rette.
12 Replacement Parts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2 8.
13 1 E spout 88507XX0 2 aerator 13085XX0 3 valve 88503000 4 hot cartridge 94009000 5 cold cartridge 94008000 6 valve mounting set 88511000 7 spout mounting set 96016000 8 pull rod 88541XX0 9 connectin.
14 Cleaning Recommendation for Hansgrohe Pr oducts Modern lavator y faucets, kitchen faucets, and showers consist of ver y different materials to comply with the needs of the market with regard to design and functionality . T o avoid damage and returns, it is necessar y to consider certain criteria when cleaning.
15 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No. 90964501-04 • Revised 02/2008 D. Accessories, connected materials and products, or related products not manufactured by Hansgrohe.
An important point after buying a device Hans Grohe 06633XX0 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hans Grohe 06633XX0 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hans Grohe 06633XX0 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hans Grohe 06633XX0 you will learn all the available features of the product, as well as information on its operation. The information that you get Hans Grohe 06633XX0 will certainly help you make a decision on the purchase.
If you already are a holder of Hans Grohe 06633XX0, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hans Grohe 06633XX0.
However, one of the most important roles played by the user manual is to help in solving problems with Hans Grohe 06633XX0. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hans Grohe 06633XX0 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
