Instruction/ maintenance manual of the product HX192 Hanns.G
Go to page of 19
19 inch TFT LCD Monitor HX192 USER’S MANUAL.
User’s Manual Before operating the monitor, please read th is manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference S t atement This equipment has been tested and found to comp ly with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual Recycling Information We, the Hanns.G care very much about our environmen t protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devi ces at the end-of-life.
User’s Manual T ABLE OF CONTENTS SAFETY NOTICE ........................................................................................... 5 PRECAUTIONS ......................................................................................... 5 SPECIAL NOTES ON LCD MONIT ORS .
User’s Manual SAFETY NOTICE 1. The changes or modifications not expr essly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord , if any , must be used in order to comply with the emission limits.
User’s Manual SPECIAL NOTES ON LCD MONIT ORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on agai n to make sure the flicker disappears.
User’s Manual BEFORE YOU OPERA TE THE MONIT OR FEA TURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions : 1280 X 1024 @60Hz • EP A ENERGY ST AR ®.
User’s Manual INST ALLA TION INSTRUCTIONS Inst all Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer secti on of the base points forward. 3. Snap the monitor into its base.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC: T urn of f your computer before performing the procedure below . 1. Connect one end of the 15-pi n D-Sub cable to the back of the monitor and connect the other end to the computer ’s D-Sub port.
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of t he monitor , then adjust the monitor ’s angle to your own preference. • Hold the st and so you do not topple the monitor when you change the monitor ’s angle.
User’s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other contro l buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.
User’s Manual FRONT P ANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor ’s power . • Power Indicator: Green — Power On mode. Orange — Power Saving mode. • MENU / ENTER: 1. Activates the OSD menu or confirms adjustments to settings.
User’s Manual HOW TO ADJUST A SETTING M M a a i i n n M M e e n n u u FUNCTION DESCRIPTION Brightness Select the 「 Brightness 」 option on the 「 Main Menu 」 . Enter the option and adjust the level. Contrast Select the 「 Contrast 」 option on the 「 Main Menu 」 .
User’s Manual Phase Adjustment Select the 「 Phase Adjustment 」 option to reduce the horizontal flicker of characters on the screen. Enter the option and adjust the level.
User’s Manual Language Select the 「 Language 」 option to change the language of the OSD. Enter the option and select a language. (Reference only , the OSD Langua ge is depended on selected model) Exit Exit the OSD menu function.
User’s Manual PLUG AND PLA Y Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B cap abilities ac cording to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of it s identity and, depending on the level of DDC used, communicate additional info rmation about its display cap abilities.
User’s Manual TECHNICAL SUPPORT (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should.
User’s Manual ERROR MESSAGE & PO SSIBLE SOLUTIONS CABLE NOT CONNECTED : 1. Check that the signal-cable is properly con nected, If the connector is loose, tighten the connector ’s screws. 2. Check the signal-cable’s connection pins for damage.
User’s Manual APPENDIX SPEC IFICA TIONS Driving system TFT Color LCD LCD Panel Size 48.2cm(19.0") Pixel pitch 0.294mm(H) x 0.294mm(V) V ideo H-Frequency 31KHz – 80KHz V -Frequency 56 – 75Hz Display Colors 16.
An important point after buying a device Hanns.G HX192 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hanns.G HX192 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hanns.G HX192 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hanns.G HX192 you will learn all the available features of the product, as well as information on its operation. The information that you get Hanns.G HX192 will certainly help you make a decision on the purchase.
If you already are a holder of Hanns.G HX192, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hanns.G HX192.
However, one of the most important roles played by the user manual is to help in solving problems with Hanns.G HX192. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hanns.G HX192 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
