Instruction/ maintenance manual of the product HW191 Hanns.G
Go to page of 22
HSG1033 HW191.
User’s Manual Before operating the monitor, please read this ma nual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interfer ence S tatement This equipment has been tested and found to comp ly with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is de signed, manufactured and tested according to some of the stri ctes t quality and environmental requirements in the world.
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environment prot ection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User’s Manual T ABLE OF CONTENTS SAFETY NOTICE ...................................................................................................... 6 PRECAUTIONS .....................................................................................
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the pa rty responsible for compliance could void the user's authority to operate the equipm ent. 2. Shielded interface cables and AC pow er cord, if any , must be used in order to com ply with the emission limits.
User’s Manual SPECIAL NOTES ON LCD MONIT ORS The following symptoms are norm al with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the s creen may flicker during initial use. T urn off the Power Switch and then turn it on again to make sure the flicker disappears.
User’s Manual BEFORE OPERA TING THE MONITOR FEA TURES • 19” W ide screen TFT Color LCD Monitor • Crisp, Clear Display for W indows • Recommended Resolutions : 1440 X 900@60Hz • EP A ENERGY.
User’s Manual INST ALLA TION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INST ALLA TION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC T urn off your computer before perform ing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s D-Sub port.
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the m onito r , and then adjust the monitor ’ s angle to your own preference. • Hold the stand so you do not topple the m on itor when you change the monitor ’ s angle.
User’s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control butt ons are located on the front panel of the monitor (See Figu re 4). By changing these settings, the picture can be adjuste d to your personal preference.
User’s Manual FRONT P ANEL CONTROL • Power Button: Press this button to switch ON/OFF monitor ’ s power . • Power Indicator: Green — Power On mode. Orange — Power Saving m ode. • MENU / RETURN: 1. T urn the OSD menu on/of f or re turn to the previous menu.
User’s Manual HOW T O ADJUST A SETTINGS BRIGHTNESS/CONTR AST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select 「 BRIGHTNESS 」 option to adjust the brightness value. CONTRAST Adjust the contrast value of the display accordin g to your preference.
User’s Manual H-POSITION Select the 「 H-POSITION 」 option to shift the screen im age to the left or right. Enter the op tion and adjust the level. [For VGA only] V -POSITION Select the 「 V -POSITION 」 option to shift the screen im age up or down.
User’s Manual 「 OSD COLOR 」 option under 「 OSD SETTING 」 menu, choose modes 1/2/3. SYSTEM AUDIO INPUT While transferring v ia the HDMI port, it is recommended to set AUDIO INPUT to HDMI; if .
User’s Manual PLUG AND PLA Y Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B c apa bilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depe nding on the level of DDC used, communicate additional information about its display capabilities.
User’s Manual TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible.
User’s Manual and make sure PC audio out put cable is connected to monitor ＇ s LINE IN port(or AUDIO IN port). [For HDMI Input only] 19.
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connect ed, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User’s Manual 29 1280×1024 @60Hz SXGA 63.981 60.02 30 1280×1024 @72Hz SXGA 76.02 71.448 31 1280×1024 @75Hz SXGA 79.976 75.025 32 1360×768 @60Hz SXGA 47.712 60.015 33 1400×1050@60Hz WXGA + 64.744 59.948 34 1400×1050@60Hz WXGA + 65.317 59.978 35 1440×900 @60Hz SXGA 55.
User’s Manual APPENDIX SPECIF ICA TIONS Driving system TFT Color LCD Size 19” LCD Panel Pixel pitch 0.285mm(H) x 0.285mm(V) H-Frequency 24.8KHz – 82KHz V i deo V -Frequency 56Hz– 76Hz Display Colors 16.
An important point after buying a device Hanns.G HW191 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hanns.G HW191 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hanns.G HW191 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hanns.G HW191 you will learn all the available features of the product, as well as information on its operation. The information that you get Hanns.G HW191 will certainly help you make a decision on the purchase.
If you already are a holder of Hanns.G HW191, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hanns.G HW191.
However, one of the most important roles played by the user manual is to help in solving problems with Hanns.G HW191. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hanns.G HW191 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
