Instruction/ maintenance manual of the product HA222 Hanns.G
Go to page of 24
HA222 HSG1099.
User ’ s Manual Before operating the monitor, please read this manual thoroughly. This m anual should be retained for future reference. FCC Class B Radio Fr equency Interference S tatement This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User ’ s Manual Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world.
User ’ s Manual RECYCLING INFORMATION We, t he Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User ’ s Manual T ABLE OF CONTENTS SAFETY NOTICE .................................................................................................. 6 PRECAUTIONS .......................................................................................
User ’ s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if an y , must be used in order to comp ly with the emission limits.
User ’ s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are norm al with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. T urn off the Power Switch and then turn it on again to make sure the flicker disappears.
User ’ s Manual BEFORE YOU OPERA TE THE MONITOR FEA TURES • 56cm / 22” W ide Screen TFT Color LCD Monitor • Crisp, Clear Display for W indows • Recommended Resolutions : 1680 X 1050 @60Hz .
User ’ s Manual INST ALLA TION INSTRUCTIONS INST ALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base.
User ’ s Manual SETTING THE MONIT OR ON THE W ALL DISSEMBLING THE ST AND BASE: 1. Disconnect all the cables and cords from the Monitor to prevent breakage. 2. Carefully place the Monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to prevent any damage to the Monitor .
User ’ s Manual MAKING CONNECTIONS CONNECTING TO A PC T urn off your computer before perform ing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s VGA port.
User ’ s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the m onitor , then adjust the monitor ’ s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor ’ s angle.
User ’ s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control butt ons are located on the front panel of the monitor (See Figu re 4). By changing these settings, the picture ca n be adjusted to your personal preferences.
User ’ s Manual FRONT P ANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor ’ s power . • Power Indicator: Green — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. T urn the OSD menu on/off or return to the previous m enu.
User ’ s Manual Resolution 640x400@70Hz ↔ 720x400@70Hz 640x400@85Hz ↔ 720x400@85Hz 640x480@60Hz ↔ 720x480@60Hz 1024x768@70Hz ↔ 1280x768@70Hz 1280x768@60Hz ↔ 1360x768@60Hz 1400x1050@60Hz .
User ’ s Manual HOW T O ADJUST A SETTINGS BRIGHTNESS/ CONTRAST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select 「 BRIGHTNESS 」 option to adjust the brightness value. CONTRAST Adjust the contrast value of the display according to your preference.
User ’ s Manual display , which does not ensure the image is shown as is or in initial scale. 「 FIT 」 ind icates scaling by the proportion of original images, which may cause the screen showing black bands.
User ’ s Manual the OSD. Enter the option and adjust the level. OSD TIME-OUT Select 「 OSD TIME-OUT 」 option to set the OSD time out from 10 to 100 seconds. Enter the option and adjust the level. OSD COLOR T o choose the color combination of the OSD window , select 「 OSD COLOR 」 option under 「 OSD SETTING 」 menu, choose modes 1/2/3.
User ’ s Manual PLUG AND PLA Y Plug & Play DDC2B Featur e This monitor is equipped with VESA DDC2B capa bilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional inform ation about its display capabilities.
User ’ s Manual TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible.
User ’ s Manual INPUT as a PC option, and make sure PC audio output cable is connected to monitor’s LINE IN port(or AUDIO IN port) . [For HDMI Input only] Addendum related to Windows 7 When you encounter display problem under W indows 7, you need to do the following: 1.
User ’ s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED : 1. Check that the signal-cable is properly conne cted, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User ’ s Manual 28 1280×960 @75Hz 74.592 74.443 29 1280×1024 @60Hz SXGA 63.981 60.02 30 1280×1024 @72Hz SXGA 76.02 71.448 31 1280×1024 @75Hz SXGA 79.976 75.025 32 1360×768 @60Hz SXGA 47.712 60 33 1400×1050@60Hz WXGA 64.744 59.948 34 1400×1050@60Hz WXGA 65.
User ’ s Manual APPENDIX SPECIFICA TIONS Driving system TFT Color LCD Size 56cm / 22’ ’ viewable LCD Panel Pixel pitch 0.282mm(H) x 0.282mm(V) H-Frequency 24KHz – 83KHz V ideo V -Frequency 56 – 75Hz Display Colors 16.
An important point after buying a device Hanns.G HA222 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hanns.G HA222 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hanns.G HA222 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hanns.G HA222 you will learn all the available features of the product, as well as information on its operation. The information that you get Hanns.G HA222 will certainly help you make a decision on the purchase.
If you already are a holder of Hanns.G HA222, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hanns.G HA222.
However, one of the most important roles played by the user manual is to help in solving problems with Hanns.G HA222. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hanns.G HA222 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
