Instruction/ maintenance manual of the product AM1000 Hamilton Electronics
Go to page of 18
AM1000 INSTALLATION INSTRUCTIONS OUTSIDE TRANSMITTER AM1000 213 CARAWAY LN Cary NC 27519 1.
.
Get Started! Pick three locations 1) a place for the transmitter 2) place for your studio or inside connection (can just be under a des k) and 3) a ground.
Now mount the transmitter to the m ast using the bracket (see bracket instructio ns). If you are not using a bracket, install transmitter to wall or acceptable confi guration. Install 102” Ante nna (Radio Shack # 21-903) to the transm itter, it screws into the t op.
Please note that changes or modifications not expressly approved by RangeMaster for compliance could void the user's authority to operate the equipment. Installing the AM1000 transmitter This unit is meant to be installed by someone who has some radio background.
3 your wire is to large to fit into the bi nding po st use a short section of wire and a wi re nut to complete the connection. Weatherproof the wire nut connecti on. It is important to keep the ground wire away from metal on the way to ground rod to get good range and provide the best lightning protection.
4 Step 4 If things look good so far take the tuning tool and rotate “TUNE” to obtai n a peak reading of the meter. When the meter peaks you are tuned. Be sure to stay away from the antenna while tuning. If you are to close to the antenna your body will affect where it tunes.
5 Now go and check your range. Use your car and your odometer to check the range. Do the final tune on “TUNE” (Check t o be sure the meter voltage is still peaked ). Adjust “AUDIO LEVEL” control for best sound on your radio. Keeping the antenna as verti cal as possible will help your range.
POWER ADJUST AM1000T Module (if installed ) COIL TUNE Audio Level CRYSTAL CAP TUNE TEST HOLES 6.
.
AM1000T Power Set / Tuning Module Power Adjust LED J13 Coil Tune Cap Tune When transmitter is turned on, the com puter will start in Power Set mode if th ere is a shunt in J1 3 (Power is set last). When you are tuning you will get better readings with the power all the way down (Power Adjust counter clockwise).
To go to the Cap Tune program just leave the shunt in J 13 for 15 seconds, the LED will turn off. Take the shun t off j13 (and then replace shunt onto J13) and you are in the Cap Tune program. To find the peak voltage using this program you need to ge t used to working with the program .
If you are using an Innovonics 222 be sure your output polarity is correct, here is how: 1. Turn the positive peaks all the way down 2. Turn the output level up until you get distortion, then back off a little (hair) for good sound.
.
COPY FEDERAL CO MMUNICATION S COMMISSION WASHINGTON, D. C. 20554 GRANT OF EQUIPMENT AUTHORIZATION COPY Certification Hamilton PCB Design 134 Wind Chime Ct.
.
.
1.0 1.00 1.1 .910 1.2 .840 1.3 .770 1.4 .720 1.5 .670 1.6 .630 1.7 .590 1.8 .560 1.9 .530 2.0 .500 2.1 .480 2.2 .455 2.3 .435 2.4 .420 2.5 .400 2.6 .385 2.7 .370 2.8 .360 2.9 .345 3.0 .335 3.1 .325 3.2 .315 3.3 .305 3.4 .295 3.5 .285 3.6 .280 3.7 .270 3.
An important point after buying a device Hamilton Electronics AM1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hamilton Electronics AM1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hamilton Electronics AM1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hamilton Electronics AM1000 you will learn all the available features of the product, as well as information on its operation. The information that you get Hamilton Electronics AM1000 will certainly help you make a decision on the purchase.
If you already are a holder of Hamilton Electronics AM1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hamilton Electronics AM1000.
However, one of the most important roles played by the user manual is to help in solving problems with Hamilton Electronics AM1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hamilton Electronics AM1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
