Instruction/ maintenance manual of the product HSU-18LEA13(T3) Haier
Go to page of 8
No .001051 Installation Manual of Room Air Conditioner Read this manual bef ore installation 1.Driver 2.Hacksa w 3.Hole core drill 4.Spanner(17,19 and 26mm) 5.T orque wrench(17mm,22mm,26mm) 6.Pipe cutter 7.Flaring tool 8.Knife 9.Nipper 12.Reamer 10.Gas leakage detector or soap-and-water solution 1 1.
Floor fixing dimensions of the outdoor unit (Unit:mm) HSU-18LEA 1 3(T3) 140 500 140 256 Fixing of outdoor unit Indoor Unit Selection of Installation Place Power Source Selection of pipe Outdoor Unit Fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizontally .
Indoor unit 1.Fitting of the Mounting Plate and Positioning of the wall Hole 2.Making a Hole on the W all and Fitting the Piping Hole Cover When the mounting plate is first fixed When the mounting plate is fixed side bar and lintel 1.
Indoor unit Fixing the indoor unit body [Other direction piping] Indoor/outdoor electric cable and drain hose must be bound with refrigerant piping by protecting tape. Cut away , with a nippe r , the lid for piping according to the piping direction and then bend the pipe according to the position of wall hole.
Indoor unit 1. If the supply cord is damaged, it must be replaced by the manuf acturer or its ser vice agent or a similar qualified person. The type of connecting wire is H05/07RN-F or 245IEC57(YZW). 2. If the fuse on PC board is broken please change it with the type of T .
Outdoor unit 1.Installation of Outdoor Unit 3.Connection 4.Attaching Drain-Elbo w 2.Connection of pipes Install according to T o bend a pipe , give the roundness as large as possib le not to crush the pipe Connecting the pipe of gas side first makes w or king easier .
Outdoor unit 5.Purging Method: 7 Push the air out of the indoor unit and piping as followes: (1) Remove the valve cap on 2-way valve in outdoor unit. (2) Loosen by 1/2 turn the flare nut of gas pipe, which is conneted to 3-way valve. (3) Loosen 2-way valve by 90 o using hexagon wrench, and after approx.
It becomes high midway . The end is immersed in water . It wav es. The gap with the ground is too small Less than 5cm There is the bad smell from a ditch 1.
An important point after buying a device Haier HSU-18LEA13(T3) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier HSU-18LEA13(T3) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier HSU-18LEA13(T3) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier HSU-18LEA13(T3) you will learn all the available features of the product, as well as information on its operation. The information that you get Haier HSU-18LEA13(T3) will certainly help you make a decision on the purchase.
If you already are a holder of Haier HSU-18LEA13(T3), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier HSU-18LEA13(T3).
However, one of the most important roles played by the user manual is to help in solving problems with Haier HSU-18LEA13(T3). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier HSU-18LEA13(T3) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
