Instruction/ maintenance manual of the product HSU-12HEA03/(BP) Haier
Go to page of 18
Please read this operation manual before using the air conditioner . SPLIT TYPE ROOM AIR CONDITIONER OPER A TION MANUAL 0010518526 HSU-09HEA03/(BP) HSU-12HEA03/(BP).
Bef ore disposing an old air conditioner that goes out of use, please mak e sure it's inop- erativ e and safe . Unplug the air conditioner in order to av oid the risk of child entrapment. It must be noticed that air conditioner system con tai ns re fr ig eran ts, wh ich req uire spe cia li - zed was te d is pos al .
3. If the fuse of indoor unit on PC board is broken,please change it with the type of T. 3.15A/ 250V. Do not obstruct or cov er the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and s wing louver.
3 Parts and Functions Indoor Unit OUTLET INLET CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE Outdoor Unit HSU-09HEA03/(BP) HSU-12HEA03/(BP) Actual inlet grille may vary from the one shown in the manual according to the product purchased Displa y board Inlet Air Purifying Filter Horizontal flap (adjust up and down air flo w.
4 Parts and Functions Hints After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal. NOTE: Cooling only unit do not have displays and functions related with heating 1.
ÇëÑ¡ÓÃͬһƷÅÆÁ½½Ú 7# µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ ·Àֹ©ҹÇ뽫µç³ØÈ¡ ³ö¡£ ÔÚʹÓÃÖÐÈçÓöÒì³£,Çë ½«µç³ØÈ¡³ö,6·ÖÖÓºóÔ.
6 Operation ON/OFF TEMP SET TIMER CLOCK SWING LOCK RESET F AN MODE 1 2 3 4 HEAL TH POWER/SOFT just press ON/OFF button and unit will run in previous status. Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status.
Press MODE button. For each press, operation Operation (1) Unit start mode changes as follows: Press ON/OFF button, unit starts. Previous operation status appears on display . (Not T imer setting) (2) Select operation mode (3) Select temp. setting Press TEMP button.
8 Operation just press ON/OFF button and unit will run in previous status. Unit runs at the speed displayed on LCD. Hints Remote controller can memorize each operation status. When starting it next time, COOL operation starts when room temp. is higher than temp.
9 Operation (5) Air flow direction adjustment After operation mode is selected, horizontal flap will open automatically according to the mode. Referring to the Fig. COOL COOL About 10 o About 10 o better set a temp. difference of 3-5 o C between indoor and outdoor temp.
10 Operation TIMER Operation Y ou can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. Set Clock correctly before starting T imer operation TIMER ON/OFF Power indicator on indoor unit lights up.
PO WER/SOFT Operation PO WER Operation PO WER Operation SOFT Operation When you need r apid he ating or cooling, you can use this funciton. Y ou can use this function when silence is needed for rest or reading. Selecting of PO WER operation Press PO WER/SOFT button.
Emergency Operation: Carry out this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, a" Pi "sound starts once, which means the start of this operation.
1 3 Maintenance 1.Open the lnlet Grille 2.Detach the standard air filter 3.Attach Air Purifying Filter 4.Attach the standard air filter (Necessar y installation) 5.Close the Inlet Grille Close the Grille surely Slide the knob slightly upward to release the filter, then withdra w it.
1 4 Maintenance For Smar t Use of The Air Conditioner Setting of proper room temperature Close doors and windows dur ing operation If the unit is not to be used f or a long time, turn off the pow er supply main s witch.
Cautions STRICT ENFORCEMENT Safety Instruction Installation W ARNING Please read the f ollowing Safety Instructions carefully prior to use. The instructions are classified into two le v els, WARNING and CA UTION according to the seriousness of possible risks and damages as follo ws.
Cautions W ARNING When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. OFF Use an exclusive power source with a circuit breaker ENFORCEMENT Connect power supply cord to the outlet completely Use the proper voltage Do not use power supply cord in a bundle.
1 7 T rouble shooting Before asking for service, check the following first. Normal Performance inspection Noise is heard Phenomenon Cause or check points The system does not restart immediately . Smells are generated. Mist or steam are blown out. Multiple check Does not work at all.
An important point after buying a device Haier HSU-12HEA03/(BP) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier HSU-12HEA03/(BP) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier HSU-12HEA03/(BP) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier HSU-12HEA03/(BP) you will learn all the available features of the product, as well as information on its operation. The information that you get Haier HSU-12HEA03/(BP) will certainly help you make a decision on the purchase.
If you already are a holder of Haier HSU-12HEA03/(BP), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier HSU-12HEA03/(BP).
However, one of the most important roles played by the user manual is to help in solving problems with Haier HSU-12HEA03/(BP). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier HSU-12HEA03/(BP) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
