Instruction/ maintenance manual of the product HDY-M60 Haier
Go to page of 16
HDY -M60 Start HDY-M60 OFF 20 min 60 min 100 min 150 min 200 min OFF 60 min 30 min Cool Warm Please read this manual carefully before operating your dryer . Retain this for future reference. Record the model and serial number of the tumble dryer . Please have this information ready for any service related enquiries.
4 9 RACK FITTING INSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 14 1 14 WIRING CIRCUIT. . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .14 IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . 1 Date Purchased: Store Purchased from: Serial No.
1 Re ad al l in str uc tio ns b ef ore u si ng th is d rye r . 2 The interior of the dryer should be cleaned periodically by qualified ser vice personnel. An excessive amount of lint build up in the interior of the dryer could result in inef ficient dr ying and pose a possible fire hazard.
2 15 Do n ot dry u nwas hed it ems in t he tu mble d ryer . 16 Fab ric so ften ers, or si mi lar pr odu cts , sh ould b e us ed a s sp ecif ie d by t he f abri c so fte ner in st ruc tion s.
Start HDY-M60 OFF 20 min 60 min 100 min 150 min 200 min OFF 60 min 30 min Cool Warm Read all instructions before using this dryer . This dryer has been designed for domestic use only .
Turning on power Before turning on the power of the dryer check whether the supply voltage is in accordance with the value indicated on the name plate. f Preparation of laundry load - The dryer can only dry laundry which has been spun dry. Do not put in laundry which is still dripping wet or has excess water.
1. Power up Insert the power plug into an appropriate power outlet that is properly installed and grounded. Operating power supply: 220-240V~50Hz. 2. Laundry loading Open the door and load the laundry into the drum of the dryer . For a more energy efficient and better drying result, make sure the load has been spun dried.
6 Dryer timer: The timer will let you set the time for up to 200 minutes to dry your clothes depending on the load of the clothes. This dryer has two program types. The light blue colour is the cool air cycle and the orange is the warm air cycle. During the cool air cycle the heater does not come on and the clothes are dried by cool air.
Cleaning the surface Wipe off any dust or dirt. Cleaning the filter screen T o ensure good ventilation effect during drying, the filter screen must be cleaned before or after each use. 1. Remove the filter Gently push together the clip on the filter screen and then pull out towards yourself.
Remove the transport packaging (fig.1) and remove the dryer rack from the top packaging (fig.2). Remove the tape on the front (fig.3 and fig.4), the wall mounting kit attached to the drum with tape on the inside and the panel film, before starting the dryer .
W ALL MOUNTING INSTRUCTIONS 1. Determine the location of the dryer on the wall and mark the bracket position. A minimum 50 mm is needed between the top of the dryer and the celling for ease of installation; If mounting above a washing machine, allow sufficient room to open the lid of the washer .
W ALL MOUNTING INSTRUCTIONS 3. I nstall the hooks to the dryer , in the inverted position, remove the 2 screws and 2 plastic plugs as indicated in Fig.1 . 4. Align the hooks as shown in Fig.2 and refit screws tightly. Install the spacers provided as Fig.
W ALL MOUNTING INSTRUCTIONS 5. With assistance, mount dryer on wall brackets. See Fig. 3 6. A second control panel with inverted symbols is supplied. Peel the release paper from the back of inverted film then place new control panel film on the surface so that the writing is the correct way around.
DRYING RACK FITTING INSTRUCTION DR YER FREE ST ANDING-UPRIGHT For ease of access, the rack is to be mounted near the dryer top. Firstly hold the rack horizontally with the two end projections pointing upwards and away from yourself.
RACK FITTING INSTRUCTION RACK STORAGE - DR YER INVERTED. T o hold the dryer rack out of the way when not in use, it will be necessary to attach the retaining clip to the base of your dryer . T o do this, firstly remove the screw located 4 cm from the right corner of the inverted dryer ( Fig.
14 The following must be confirmed before calling for service: Problem Possible Cause The dryer does not start The drying result is not good -Is the dryer plugged in? -Is the power on? -Is the door cl.
An important point after buying a device Haier HDY-M60 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haier HDY-M60 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haier HDY-M60 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haier HDY-M60 you will learn all the available features of the product, as well as information on its operation. The information that you get Haier HDY-M60 will certainly help you make a decision on the purchase.
If you already are a holder of Haier HDY-M60, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haier HDY-M60.
However, one of the most important roles played by the user manual is to help in solving problems with Haier HDY-M60. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haier HDY-M60 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
