Instruction/ maintenance manual of the product Mini-DIN Haicom
Go to page of 30
User Manual HI-204E Mini-DIN GPS Receiver HI-204E Mini-DIN GPS Receiver.
1 HI-204E WATERPROOF GPS Receiver HI-204E WATERPROOF GPS Receiver.
2 General description of what GPS is and how it w orks. GPS (Global P ositioning System) is the only system today able to show you your exact position on the Ear th anytime, in any weather , anywhere. GPS satellites, 24 in all, orbit at 11 ,00 0 na uti cal mil es a bove t he E ar th .
3 Although GPS was designed f or militar y use, many thousands of civi lians make use of it. The satellites actually broadcast two signals, one is only formilitar y use, and the ther can be used b y both militar y and civilians.
4 PS/ 2 Connector Color Function CN1 Green TX 5 White RX 4 Red VCC 2 Black GND 1 1 3 5 2 4 6 1 1 2 2 1800±30mm GLOBAL POSITIONING SYSTEM HI-204E GPS RECEIVER Pin Assignment Connectors Mini Din: 6 pin male connector Wire: 3.
5 P ocket PC HI-204E PS/II GPS receiver Can Connecting to a f emale PS/II Connector . One end from the female Connector is +12V car charger (charging PD A and GPS receiver simultaneously) the other end f or m the f emale PS/II connector is the PD A connector for connecting your PD A.
6 1 . H I - 2 0 4E S e r i e s I n t r o d u c ti o n s HI-204E is a GPS receiver with PS/II mini-DIN interf aces and built-in activ e antenna for high sensitivity to tracking signal . HI-204 E is well suited to syste m integrat ion and users who use any kinds of mobile de vices, such as , PD A, notebook PC, T ab let PC, etc.
7 Optional Accessories: • PS/II to PDA connector and car charger • PS/II to DB9 adapting cable • PS/II to USB adapting cable HI-204E-XXXX (P ocket PC Plug) HI-204E-DB9 HI-204E-USB.
8 SECTION 1 INTRODUCTION 1.1 O VER VIEW F ast Acquisition Enhanced Sensitivity 12 Channel GPS Sensor Module The HI-204E is a compact all-in-one GPS module solution intended for a broad r ange of Original Equipment Manuf acturer (OEM) products, where fast and easy system integration and minimal de velopment risk is required.
9 Satellite-based augmentation systems, such as W AAS and EGNOS, are supported to yield improved accuracy . Both the L VTTL-level and RS232-le vel ser ial interface are provided on the interface connector . Supply voltage of 3.3V , or 3.8V~12V are suppor ted.
10 SECTION 2 RECEIVER OPERATION Upon power up, after initial self-test has completed, the HI-204E will begin satellite acquisition and tracking process. Under nor mal open-sky condition, position-fix can be achieved within appro ximately 35 seconds (within 10 seconds if valid ephemeris data is already collected fr om r ec en t us e) .
11 As soon as GPS signal is acquired and trac ked, the HI-204E will transmit valid navigation information through its ser ial interface . The navigation data contains follo wing information: • Recei.
12 2.1 TECHNICAL SPECIFICA TIONS 2.2 LED INDICA T OR FEA TURES Receiver T ype Accuracy Startup Time Reacquisition Sensitivity Update Rate Dynamics Operational Limits Serial Interface Protocol Datum Interface Connector Input V oltage Current Consumption Dimension Weight Operating T emperature LED flashing 0.
13 SECTION 3 HARDWARE INTERFACE 3.1 MECHANICAL DIMENSIONS 73±0.2 I/O Cable I/O Cable I/O Cable Build-in patch antenna LED indicator Magnetic CPU T op Vie w Lateral View Bottom View 69±0.
14 HI-204E Lateral View 3.2 PINOUT DESCRIPTION Pin Number 1 2 3 4 5 6 Signal Name Serial Data Out 1 Serial Data In 1 Serial Data Out 2 Serial Data In 2 P ower Ground Description Asynchronous serial ou.
15 3.3 ONE-PULSE-PER-SECOND (1PPS) OUTPUT The one-pulse-per-second output is provided f or applications requir ing precise timing measurements. The output pulse is 1usec in duration. Rising edge of the output pulse is accurate to +/-1usec with respect to the star t of each GPS second.
16 As long as enough satellite signals are received to generate valid position fixes , the 1PPS output remains synchroniz ed to the GPS second, and the 1PPS V alid Signal remains active .
17 SECTION 4 SOFTWARE INTERFACE Thi s sec tion de scr ibe s t he de tail s o f the se ria l p or t commands through which the HI-204E is controlled and monitored. The serial port commands allow users to set the receiver parameters, configure output message type, and retriev e status information.
18 4.1.1 NMEA Messages The serial interface protocol is based on the National Marine Electronics Association's NMEA 0183 ASCII interface specification. This standard is fully define in "NMEA 0183, V ersion 3.01" The standard ma y be obtained from NMEA, www .
19 Note: The chec ksum field star ts with a '*' and consists of 2 characters representing a hex number . The checksum is the e xclusive OR of all characters between '$' and '*'. Field 1 2 3 4 5 6 7 8 9 10 11 12 13 Example 104549.
20 4.1.3 GLL - LA TITUDE AND LONGITUDE, WITH TIME OF POSITION FIX AND ST A TUS Latitude and longitude of current position, time, and status. Format: $GPGLL,<1>,<2>,<3>,<4>,<5>,<6>,<7>*<8><CR><LF> Example: $GPGLL,2447.
21 4.1.4 GSA - GPS DOP AND A CTIVE SA TELLITES GPS receiver operating mode , satellites used for na vigation, and DOP values . Format: $GPGSA,<1>,<2>,<3>,<3>,<3>,<3>.
22 4.1.5 GSV - GPS SA TELLITE IN VIEW Number of satellites in view , PRN number , ele vation angle , azimuth angle, and C/No . Only up to f our satellite details are transmitted per message. Additional satellite in vie w information is sent in subsequent GSV messages.
23 4.1.6 RMC - RECOMMANDED MINIMUM SPECIFIC GPS/TRANSIT D A T A Time, date, position, course and speed data. Format: $GPRMC,<1>,<2>,<3>,<4>,<5>,<6>,<7>,<8>,<9>,<10>, <11>,<12>*<13><CR><LF> Example: $GPRMC,104549.
24 4.1.7 VTG - COURSE O VER GR OUND AND GROUND SPEED V elocity is giv en as course over g round (COG) and speed ov er ground (SOG). Format: GPVTG,<1>,T ,<2>,M,<3>,N,<4>,K,<5>*<6><CR><LF> Example: $GPVTG,221.
25 4.1.8 ZD A TIME AND D A TE Format: $GPZD A,<1>,<2>,<3>,<4>,<5>,<6>*<7><CR><LF> Example: $GPZD A,104548.04,25,03,2004,,*6C<CR><LF> Binary Messages See Binary Message Protocol User's Guide for detailed descriptions.
26 MECHANICAL CHARACTERISTICS 42.0 31.5 25.0 35.0 3.0 0.2 0.2 4.0 25.0 17.0 5.5 36.1 5.0 6.0 1.5 1.0 14.8 1.3 2.0 3.9 11.0 4.0 1.0 5.0 9.5 5.5 41.6 42.
27 APPENDIX B DEF AUL T V ALUES The product has the follo wing factory preset default values: Datum: NMEA Enable Switch: Baud Rate: Elev ation Mask: DOP Mask: Receiver Operating Mode: Commands can be issued to the HI-204E to change the settings of the receiver .
28 TROUBLESHOO TING Problem Reasons Solutions No P osition output but timer is counting Weak or no GPS signal can be received at the place of HI-204E unit Place the HI-204E under an open space, then, .
WATERPROOF GPS Receiver WATERPROOF GPS Receiver.
An important point after buying a device Haicom Mini-DIN (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Haicom Mini-DIN yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Haicom Mini-DIN - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Haicom Mini-DIN you will learn all the available features of the product, as well as information on its operation. The information that you get Haicom Mini-DIN will certainly help you make a decision on the purchase.
If you already are a holder of Haicom Mini-DIN, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Haicom Mini-DIN.
However, one of the most important roles played by the user manual is to help in solving problems with Haicom Mini-DIN. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Haicom Mini-DIN along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
