Instruction/ maintenance manual of the product TA1100 Hafler
Go to page of 12
.
T A1 100/T A1600 Signal-to-Noise: >102dB below rated output “A” weighted CMRR: >65dB at 1kHz Input Impedance: 47k Ω per phase balanced 47k Ω unbalanced Gain: 29dB maximum Damping Factor:.
ii NOTICE - IMPORTANT SAFETY INFORMATION CAUTION RISK OF ELECTRIC SHOCK DO NO T OPEN W ARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NO T EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. ! 1. Read Instructions All the safety and operating instructions of your Hafler equip- ment should be read before power is applied to the equipment.
1. LEA LAS INSTRUCCIONES T odas las instrucciones de seguidad y operación de su equipo Hafler , deben ser leídas antes de que el equipo sea conectado dléctricamente. 2. CONSER VE EL MANUAL DEL PROPIET ARIO Estas instrucciones de seguridad y operación, deben ser conser- vadas para futuras referencias.
iv PERFORMANCE SPECIFICA TIONS ..................................................................................................................................................i SAFETY PRECAUTIONS .....................................................
– 1 – The Hafler T A1 100 and T A1600 are two channel, two rack height, convection-cooled, MOSFET power amplifiers suitable for use in the most demanding applications of critical listening and instrument amplification.
2 Design Features 1. Input level control 2. Clip/Thermal/ Protect LED 3. Power switch 4. Headphone jack 1. Balanced 1/4” input 2. Unbalanced RCA input 3.
LOCA TION The T A1 100 and T A1600 power transformer can generate a substantial magnetic field, so caution should be exer cised in the placement of low level components such as a tape deck, mixer or mic preamp to avoid inducing noise in the low level circuitry .
1/4" TRS Balanced Input Check output of source unit for proper signal polarity Tip = (+) Ring = (–) Sleeve = GND 1/4" TRS Unbalanced Input Tip = (+) Sleeve = GND 4 Operation T ip Ring Slee.
T A 1600 - SHORT CIRCUIT PROTECTION The T A1600 amplifier cir cuit has no need for sonically degrading voltage and current limiting circuits. T o protect the amplifi- er from problems which may occur in the speaker line there is an overload detection cir cuit.
Please contact Hafler for any W arranty issues. Hafler offers the following limited warranty on Hafler products. • Length of W arranty 1 year on T A1 100 and T A1600 90 days on all B-Stock electronics (receipts are required) • What is Covered This warranty applies only to products sold to the original owner (non-transferable).
® HAFLER A DIVISION OF ROCKFORD CORPROA TION 546 SOUTH ROCKFORD DRIVE TEMPE, ARIZONA 85281 U.S.A. 480-967-3565 / 1-888-HAFLER1 WWW .HAFLER.COM M.J.T .
An important point after buying a device Hafler TA1100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hafler TA1100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hafler TA1100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hafler TA1100 you will learn all the available features of the product, as well as information on its operation. The information that you get Hafler TA1100 will certainly help you make a decision on the purchase.
If you already are a holder of Hafler TA1100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hafler TA1100.
However, one of the most important roles played by the user manual is to help in solving problems with Hafler TA1100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hafler TA1100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
