Instruction/ maintenance manual of the product 73992 GSW
Go to page of 24
W ARNING: If the information in these instructions is not followed exactly , a fire or explosion may result causing property damage, per- sonal injury or death. W ARNING: Improper inst allation, adjustment, alter- ation, service, or maintenance can cause injury or property damage.
- 2 - Y our safety and the safety of others is very import ant. W e have provided many import ant safety messages in this manual and on your appliance.
- 3 - T&P V AL VE HOT W A TER OUTLET DRAIN V AL VE POWER TRANSFORMER (IF APPLICABLE) FUSES (POWER CIRCUIT) (IF APPLICABLE) CONT ACT ORS FUSES (CONTROL CIRCUIT) HEA TING ELEMENTS PLUGS INPUT TERMINAL BLOCK CONTROL THERMOST A T ANODE (UNDER PLASTIC CAP) MANUAL HIGH LIMIT RESET CLEANOUT COLD W A TER INLET NOTES: 1.
- 4 - 17 ° 22 ° 28 ° 33 ° 39 ° 44 ° 50 ° 56° 6 1° 6 7° 7 2° 7 8° 6 20 , 4 78 31 0 235 18 5 15 5 132 11 7 10 2 95 8 3 79 7 2 68 9 30 , 7 17 4 66 3 48 28 0 23 5 20 1 17 4 15 5 14 0 12 9 11 7 10 6 98 12 40 , 9 56 6 21 4 66 37 1 31 0 26 5 23 1 20 8 18 5 17 0 15 5 14 4 13 2 13 .
- 5 - Gener al A pplicab le Codes In addition to the inst allation instructions found in this man- ual, the water heater must be inst alled in accordance with all local and provincial or st ate codes .
- 6 - • Must be inst alled to allow complete drainage of both the valve and discharge line. • Must not discharge so as to come in cont act with any electrical p art or wiring. Under no circumst ances is the manufacturer to be held responsible for any water damage in connection with this water heater .
- 7 - Impor tant: Heat must not be applied to the water fittings on the heater as they may cont ain nonmet allic p art s. If sol- der connections are used, solder the pipe to the adaptor before att aching the adaptor to the hot and cold water fit- tings.
- 8 - the water heater . If the heater is located a long dist ance away from the electrical supply , the wire size of the branch circuit should be increased. The volt age measured at the heater should not be less than 3% lower than what is meas- ured at the supply .
- 9 - T emper a tur e Contr ol All electric water heaters feature fully automatic controls to regulate the water temperature. The thermost at supplied with the water heater may be either an immersion or a sur- face mounted type. Both types of thermost at s use cont act relays to energize the electric heating element s.
- 10 - 20 8V 2 40 V 27 7V 3 47 V 48 0V 60 0V 2 08 V 24 0V 4 80 V 60 0V 6 20 00 2 8.8 25.0 21 . 7 1 7.3 12.5 10 . 0 1 6.7 14.4 7. 2 5 . 8 9 30 00 4 3.3 37.5 32 . 5 2 5.9 18.8 15 . 0 2 5.0 21.7 10.8 8. 7 12 40 00 5 7.7 50.0 43 . 3 3 4.6 25.0 20 . 0 3 3.
- 11 - FIGURE 5: Control Circuit (Canada) INPUT TERMINAL BLOCK 3A FUSE OPTIONAL CONTROL TRANSFORMER (USED ON 480 OR 600V ONL Y) HIGH-LIMIT THERMOST A T 480 OR 600V CONT ACT ORS PRIMARY SECONDARY RED BLACK N 240V THERMOST A T C3 (IF APPLICABLE) FOR 3 ELEMENTS CONFIGURA TION.
- 12 - FIGURE 8: 6 Element, 3 Phase Power Circuit (Canada) FIGURE 7: 6 Element, 1 Phase Power Circuit (Canada) INPUT TERMINAL BLOCK CONT ACT ORS RED BLACK LOWER ELEMENTS BLACK BLACK BLACK RED RED RED .
- 13 - FIGURE 9: 9 Element, 1 Phase Power Circuit (Canada) FIGURE 10: 9 Element, 3 Phase Power Circuit (Canada) INPUT TERMINAL BLOCK CONT ACT ORS RED BLACK LOWER ELEMENTS BLACK BLACK BLACK RED RED RED.
- 14 - FIGURE 1 1: 3 Element Control Circuit (USA only) FIGURE 12: 3 Element Power Circuit (USA only) INPUT TERMINAL BLOCK 3A FUSE CONTROL TRANSFORMER HIGH-LIMIT THERMOST A T 480V CONT ACT ORS PRIMARY.
- 15 - FIGURE 13: 6 Element Control Circuit (USA only) FIGURE 14: 6 Element Power Circuit (USA only) INPUT TERMINAL BLOCK 3A FUSE CONTROL TRANSFORMER HIGH-LIMIT THERMOST A T 480V CONT ACT ORS PRIMARY .
- 16 - FIGURE 15: 9 Element Control Circuit (USA only) FIGURE 16: 9 Element Power Circuit (USA only) INPUT TERMINAL BLOCK 3A FUSE CONTROL TRANSFORMER HIGH-LIMIT THERMOST A T 480V PRIMARY SECONDARY N 1.
- 17 - FIGURE 17: T ransformer PT75MLI (USA only) 460V 230V 208V SECONDARY 1 15V , 0.65A H4 H3 H2 H1 X1 X2 FIGURE 19: T ransformer PT75MRMA (USA only) 600V 480V 416V SECONDARY 0.63A H5 H4 H3 H1 X1 X4 240V H2 X3 X2 FIGURE 18: T ransformer PT75MGJ (USA only) 380V 277V 208V SECONDARY 120V , 0.
- 18 - Gener al CA UTION! NEVER APPL Y ELECTRICAL POWER TO THIS W A TER HEA TER UNLESS IT IS COMPLETEL Y FULL OF W A TER. T O PREVENT DAMAGE T O THE T ANK AND HEA TING ELEMENTS, THE T ANK MUST BE FILLED WITH W A TER BEFORE USE. W A TER MUST FLOW FROM THE HOT W A TER F AUCET BEFORE APPL YING POWER.
- 19 - Gener al Do not attempt to rep air water heater . Call your authorized dealer for service. Shut of f the electric power whenever the water supply is turned of f. Before calling for service, check that: 1. The heater is properly filled. 2. The electrical supply has not been interrupted.
- 20 - Discolour ed W a ter • W ater rich in iron or other minerals can produce red or brown st aining. Heating water generally worsens this situation. • Black water can be an indication of organic cont ami- nates in the water supply . This can be problematic in areas where the water is obt ained from surface or con- t aminated sources.
- 21 - Wa ter hea ter is noisy: 1. The heater makes sizzling and hissing noises operating. • The accumulation of sediment or lime scale may be the cause. The sounds are normal; however , the t ank bot- tom and element s should be cleaned. Follow the instruc- tions given in “Draining, Flushing and Sediment Removal”.
- 22 - HOT W A TER OUTLET ANODE (UNDER PLASTIC CAP) T&P V AL VE DRAIN V AL VE CLEANOUT PORT (BEHIND ACCESS DOOR) COLD W A TER INLET PLUGS FOR UNUSED ELEMENT LOCA TIONS ELEMENTS FIGURE 21: Possible.
- 23 - Installa tion Instr uctions Gener al The inst allation of the floor sealant is a requirement for NSF construction compliance. T ools And Ma terials R equir ed: 1.
See Rating Label Serial Number prefix for W arranty Code. Reduced warranty period applies to Newfoundland. W arranty Code: P R S T U V W Y S tandard W arranty Y ears: 3 5 6 7 8 9 10 12 Reduced W arran.
An important point after buying a device GSW 73992 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GSW 73992 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GSW 73992 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GSW 73992 you will learn all the available features of the product, as well as information on its operation. The information that you get GSW 73992 will certainly help you make a decision on the purchase.
If you already are a holder of GSW 73992, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GSW 73992.
However, one of the most important roles played by the user manual is to help in solving problems with GSW 73992. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GSW 73992 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
