Instruction/ maintenance manual of the product P400E Grindmaster
Go to page of 36
Shuttle Bre wer & Airpot/Shuttle Bre wer s Operation and Instruction Manual F or Models P300E, P400E, RAP300E, RAP400E, RAPS300E, RAPS400E Installation: See rough-in dra wings in this manual f or dimensions and locations of electric and water input.
Pag e 2 Shuttle Brewer s & Airpot/Shuttle Brewer s Installation (con't) Electric Hook-up 1) The electric ratings f or your bre wer are printed on its nameplate. T ypical electric ratings are: P300, P400, RAP300, RAP400 Optional 120/208V , 3.8kW , 18A or 120/240V 5.
Pag e 3 Operation 1) RAPS Brew ers require the accessor y warmer base placed ov er the pegs on the brew shelf bef ore brewing into a shuttle . Plug the base into the receptacle on the side of the brew er . The receptacle is only energized when a shuttle is in place .
Pag e 4 Adjustments All adjustable components are located under the top co v er . T o access these par ts: 1) Shut off the electric line to the brewer or unplug the bre wer . 2) Remov e the single screw f astening the top cov er . Remov e the top cov er .
Pag e 5 Two Batch Timer with Knob Adjustment, See Figure 2: This timer is adjustable from 15 seconds to 5 min utes. Locate the adjustment knobs under the top cov er . Set this timer by adjusting the knob . The batch selector s witch picks the adjustment potentiometer which the timer will see.
Pag e 6 T o Adjust the Bypass: 1) Shut off and open brew er as described at the beginning of the adjustments section. 2) Locate the bypass v alve f or the brew head you wish to adjust. V alve is on the right and front of the BREW v alve . 3) Open the v alve (counter cloc kwise) to the desired setting.
Pag e 7 4) If the maximum temperature adjustment needs to be increased, insert a small flat screwdriver into the shaft. T ur n the calibration screw counter cloc kwise to increase the maximum temperature . Optional Solid State Thermostat: This control maintains temperature within 3°F .
Pag e 8 Cleaning After Each Bre w: 1) Dispose of grounds and rinse brew bask et. 2) Rinse shuttle or air pot containers bef ore reuse. Every Day: 1) W ash brew basket with w ar m soap y water . The wire basket is remov able to aid cleaning. 2) Remov e spray head(s), located abo v e brew bask et(s), using glov es or a heavy to wel.
Pag e 9 W eekly or Bi-W eekly , Depending on Use 1) Fill shuttles with one gallon, 2/3 full, of hot water . 2) P our into the shuttle liners the recommended concentration of ur n cleaner (e xcessiv e amounts of cleaner will attack the stainless steel).
Pag e 1 0 Service (con't) Drain W ater T ank Alwa ys empty the tank before shipping. Note: Brew er ma y contain ov er 5 gallons of hot water . 1) Prepare a heat resistant container to drain tank w ater into . 2) Shut off pow er to the brewer . 3) Remov e the front access panel.
Pag e 1 1 T r oubleshooting: Filling, Heating, and Bre wing Overfilling water tank even when power is off. Fill valv e not sealing properly . Fill valv e installed backw ards. W ater entering tank continuously , usually slowly . Look f or direction of arrow on v alv e body .
Pag e 1 2 Shuttle Brewer s & Airpot/Shuttle Brewer s If you still need help, call our Technical Service Department at (502) 425-4776 or (800) 695-4500 (USA & Canada only) Monday thru Friday 8 am - 8 pm EST or an authorized service center in your area.
Pag e 1 3 T r oubleshooting: Filling, Heating, and Bre wing Brewing Pr oblems The brewing system consists of the f ollowing components: • Star t and Stop , switches located in the top control panel. • Brew Timer , located in the top control section under the top cover .
Pag e 1 4 P ar ts Illustration for Models P300E & P400E Shuttle Brewer s & Airpot/Shuttle Brewer s Item Pa r t # Description Item Pa r t # Description 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 1.
Pag e 1 5 P ar ts Illustration for Model RAP400E Shuttle Brewer s & Airpot/Shuttle Brewer s Item Pa r t # Description Item Pa r t # Description 1 A548-072 LEG, R UBBER (RAP400) 11 A515016 PILO T L.
Pag e 1 6 P ar ts Illustration for Model RAPS400E Shuttle Brewer s & Airpot/Shuttle Brewer s FR ONT Item Pa r t # Description Item Pa r t # Description 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 16 A.
Pag e 1 7 Shuttle Brewer s & Airpot/Shuttle Brewer s TOP (COVER REMOVED) FRONT FRONT (COVER REMOVED) 5 4 3 2 1 11 10 16 20 22 9 17 19 18 23 15 14 13 12 8 7 6 21 P ar ts Illustration for Model VSB-.
P ar ts Illustration for Shuttle CS-LL Item Pa r t # Description 1 A537-053 F A UCET MODEL ES 2 A522078 SHANK W/ CHROME BONNET 3 A718-018 GA UGE ASSEMBL Y 4 A725-092 KIT , SHUTTLE LID A713-027 SS SHUTTLE CO VER (not shown)* 5 A548-142 LID RET AINING CLIP 6 A548-140 A61365 LID ST OPPER W/ O-RING * S.
Pag e 1 9 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model P-300.
Rough-In Drawing f or Model P-400 Pag e 2 0 Shuttle Brewer s & Airpot/Shuttle Brewer s.
Pag e 2 1 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model RAP-300.
Rough-In Drawing f or Model RAP-400 Pag e 2 2 Shuttle Brewer s & Airpot/Shuttle Brewer s.
Pag e 2 3 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model RAPS-300.
Pag e 2 4 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model RAPS-400.
Pag e 2 5 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model VSB-300 W W W W W A TER IM S.
Rough-In Drawing f or Model VSB-400 Pag e 2 6 Shuttle Brewer s & Airpot/Shuttle Brewer s.
Pag e 2 7 Shuttle Brewer s & Airpot/Shuttle Brewer s Wiring Diagram f or P300E/P400E, with 1 Batch Timer NO TE: THIS DRAWING SHO WS COMPONENTS ON ST ANDARD MODEL ONL Y .
Wiring Diagram f or P300E/P400E, with 2 Batch Timer NO TE: THIS DRAWING SHO WS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS Pag e 2 8 Shuttle Brewer s & Airpot/Sh.
Pag e 2 9 Shuttle Brewer s & Airpot/Shuttle Brewer s Wiring Diagram f or RAP300E/400E NO TE: THIS DRAWING SHO WS COMPONENTS ON ST ANDARD MODEL ONL Y .
Wiring Diagram f or RAPS 300/400E NO TE: 1) TWO SETS OF RECEPT ACLE COMPONENTS ONL Y PRO VIDED ON TWIN RAPS400E MODEL. DELETE GR OUP IN D ASHED BO X FOR RAPS300E. 2) THIS DIAGRAM SHO WS COMPONENTS ON ST AN- D ARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS.
Pag e 3 1 Shuttle Brewer s & Airpot/Shuttle Brewer s Wiring Diagram #091-548 NO TE: 1) ONE GROUP OF WARMER COMPONENTS PER BREW HEAD ON P AND RAPS MODELS. 2) TRANSFORMER MUST BE USED WHEN NEUTRAL LINE IS NO T PRO VIDED . 3) IF MODEL RAP , DELETE W ARMER COMPONENTS.
Wiring Diagram #091-182 T3 T3 T3 1 1 T4 A T2 T3 T3 T4 T4 T4 B T2 T3 T3 1 1 T1 C T3 T3 T3 T1 T1 T4 D T2 T3 T3 T1 T1 T4 E T2 T3 T3 T1 T1 T2 F NO TE: USE WIRE NUT FOR 1 - 1 CONNECTION 5000 W A TT / 240V HEA TERS * SEP ARA TE 120V REQUIRED FOR CONTR OLS (3 AMP LOAD) 2.
Pag e 3 3 Shuttle Brewer s & Airpot/Shuttle Brewer s Notes.
Pag e 3 4 Shuttle Brewer s & Airpot/Shuttle Brewer s Notes.
Pag e 3 5 Shuttle Brewer s & Airpot/Shuttle Brewer s Notes.
Grindmaster Corporation 4003 Collins Lane Louisville, KY 40245 USA (502) 425-4776 (800) 695-4500 F AX (502) 425-4664 www .grindmaster .com © Grindmaster Cor poration, 1995 PRINTED IN USA Shuttle Bre .
An important point after buying a device Grindmaster P400E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Grindmaster P400E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Grindmaster P400E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Grindmaster P400E you will learn all the available features of the product, as well as information on its operation. The information that you get Grindmaster P400E will certainly help you make a decision on the purchase.
If you already are a holder of Grindmaster P400E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Grindmaster P400E.
However, one of the most important roles played by the user manual is to help in solving problems with Grindmaster P400E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Grindmaster P400E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
