Instruction/ maintenance manual of the product 12031303 Gravely
Go to page of 22
OPERA T OR’S MANU AL PT O GRASS COLLECTION SY STEM DESIGNED FOR: ASSEMBL Y OPER A TION MAINTENANCE MODEL 12031303 GR A VEL Y 100 SERIES MOWERs MANU AL P AR T#: Q0347 $4.
2 PT O GRASS COLLECTION SY STEM T ABLE OF CONTENTS SECTION P AGE Safety - ------------------------------2 Safety Alert Symbols ----------------------3 W arranty -----------------------------4 I INTROD.
3 SAFETY WARNING! WARNING! WARNING! WARNING! Saf ety Aler t Symbol Saf ety Signs NEVER ONL Y AFTER ST OPPING THE MOWER’S ENGINE AND WAITING FOR ALL MO VING P ARTS T O COME TO A COMPLETE ST OP .
4 PECO LIMITED WARRANTY FOR NEW PR ODUCTS A. WHA T IS WARRANTED? 1. PRODUCT WARRANTY : ALL DEFECTIVE P ARTS MUST BE RETURNED TO PECO FOR INSPECTION T O DETERMINE V ALIDITY OF WARRANTY CLAIMS. 2. P ARTS REPLACED DURING WARRANTY : B. SECURING WARRANTY ADJUSTMENTS.
5 SECTION I INTR ODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer . Y our collection system has been designed to give you a low maintenance, simple, and effective way to collect the grass clippings from your mower .
6 2-2 Muf fler Guard Installation Locate the two exhaust diverters (P#J0251 w/ 1-1/4” ID, P#J0250 w/ 1-3/8” ID) and clamp kit P#(X1046) provided in the hardware bag. Fasten the correct size exhaust deflector onto the mower ’ s exhaust and aim the exhaust as shown in Figure 2-2.
2-3 Attaching The T op Main F r ame Assembly Place the top main frame assembly P#(00197800) (Figure 9) onto the main frame legs and fasten each side by using (1) 3/4”-10 x 1-1/2” HHCS P#(05959600), (1) 3/4”-10 nyloc nut P#(06540800), (1) ½”-13 x 1” HHCS P#(05947100), and (1) pivot frame handle P#(00194900).
8 Exploded View Of The A0549 - Bagger Assembly (2) K1 144 - 5/16”-18 x 1” CARRIAGE BOL T (6) K1 142 - 5/16”-18 x 3/4” CARRIAGE BOL T (4) K1010 - 1/4”-20 x 5/8” CARRIAGE BOL T (1 LEFT , 1 R.
9 Exploded P ar ts V iew Exploded View Of The Blower Assembly Exploded View Of The A0506 - PTO Assembly 1 2 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3.
P ar ts V iew 10 A0515 WEIGHT KIT (1) B2220 WEIGHT BAR (1 LEFT , 1 RIGHT) B0188 WEIGHT BRACKETS (1) HB0186 HARDWARE BAG A0553 UNIT ASSEMBL Y (1) 6” x 20” UPPER HOSE (1) 8” x 31” LO WER HOSE (2) J6006 7”-8” HOSE CLAMPS (1) HB0256 HARDWARE BAG (3) G0002 3.
11 2-6 Cam Assembly Adjustment The cam assembly P#(A0422), which controls the blower belt tension, comes from the factory pre-adjusted. If the belt is too tight or becomes too loose, remove the hair p.
12 2-10 Boot Installation First, remove the deflector shield by pulling out the locking pin and lifting the shield out of deck mount tube. T o install the boot to the mower deck, attach the boot plate.
13 Note: Note: When bolting the boot and boot plate together , the head of the bolt is placed from the inside of the boot. This will prevent grass from collecting on the bolts. The Mower ’ s Deflector Shield Has Been Removed In The Following Photo For Clarity .
14 2-16 Blow er Cone Installation Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially thread the bolts into each of the two tabs located on the blower housing. Place blower cone so the two tabs line up with the bolts then tighten completely .
15 2-18 Installation/R emo val Of Collection Bags T o install the bag onto the bag ring, first make sure the bag ring end caps are fastened to the bag ring. Place the seam openings of the bag onto the bag ring openings and turn the bag until the slot bracket in the bag ring is protruding from the opening in the bag (Figure 2-18a).
16 2-19 Final Checks 3-1 General Safety 3-2 Operation And Tips On Mo wing T o check the operation of the safety interlock harness perform the following: A. Start mower B. While seated in the operator ’ s seat, rotate the engagement handle of the collection system away from the mower .
17 3. Make sure all shields are in place and in good condition. Repair or replace any missing or damaged shields. 4. Perform lubrication per paragraph 4-2. 5. Listen for abnormal sounds, which might indicate loose parts, damaged bearings, or other damage.
SAFETY DECALS T o promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning.
19.
NO TES 20.
NO TES 21.
P .O . BO X 1197 ARDEN, NORTH CAR OLINA 28704 (800) 438-5823 OR (828) 684-1234 F AX: (828) 684-0858 EMAIL: peco@lawn vac.com WEBSITE: www .lawn vac.com P PEC O PEC O P P P P PEC O PEC O PEC O T ur n a.
An important point after buying a device Gravely 12031303 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Gravely 12031303 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Gravely 12031303 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Gravely 12031303 you will learn all the available features of the product, as well as information on its operation. The information that you get Gravely 12031303 will certainly help you make a decision on the purchase.
If you already are a holder of Gravely 12031303, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Gravely 12031303.
However, one of the most important roles played by the user manual is to help in solving problems with Gravely 12031303. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Gravely 12031303 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center