Instruction/ maintenance manual of the product GC-1402F Graco Inc.
Go to page of 20
Operation Formula-X Chop GC-1402F ENG Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. Low emission external-mix dispense gun for use with polyester resin and gel coat. For professional use only .
2 GC-1402E Contents W arnings .......................................................... 3 Important Safety Information ......................... 5 Grounding .............................................. .......... 6 Set-Up ..........................
3 GC-1402E W arnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure- specic risk. Refer back to these warnings.
4 GC-1402E W ARNING SKIN INJECTION HAZARD High-pressure uid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the body .
5 GC-1402E Important Safety Information Methyl Ethyl Ketone Peroxide (MEKP) MEKP is among the more hazardous materials found in commercial channels. Proper handling of the “unstable (reactive)” chemicals presents a denite challenge to the plastics industry .
6 GC-1402E This equipment needs to be grounded. Ground the dispense gun through connection to a GlasCraft approved grounded uid supply hose. Check your local electrical code and related manuals for detailed grounding instructions of all equipment in the work area.
7 GC-1402E Hose Attachment 1. Push in and rotate the trigger lock to stop the trigger from being activated. 2. Attach the (black p/n 21694-25) material hose to the material inlet tting on the back of the gun. 3. Attach the (red) atomize air tubing to the atomize air inlet tting on the back of the gun.
8 GC-1402E Repair Kits Part Number Description 23792-00 GUN AIR KIT 23793-00 GUN SEAL KIT 23732-00 GUN FLUID V AL VE KIT Standard Equipment Part Number Description 23750-03 FORMULA X CHOP DISPENSE GUN.
9 GC -1402E REVISION C 23750-03 Formula X Chop Dispense Gun Assembly Drawings.
10 GC-1402E REVISION C 23750-03 Formula X Chop Dispense Gun Assembly Drawings 189018.
11 GC-1402E REVISION C Part Number Description Qty . 10773-28C SCREW 1 13867-05 O-RING 1 13867-07 O-RING 3 15845-01 5/32in. BALL DRIVER 1 18383-02 1/4in.
12 GC-1402E T o relieve uid and air pressures: 1. Push down Y ellow slide valve, P/N 21402-00 to bleed off air to system. 2. Open P/N 21228-00 on catalyst pump to recirculation position. 3. Open P/N 21 192-00 on bottom of material pump. 4. V erify the trigger lock is engaged.
13 GC-1402E Parts Replacement Procedure Formula X Chop Gun Before performing maintenance on the dispense gun, follow Pressure Relief Procedure. Due to the different o-ring materials and lubricants used in the dispense guns, never submerge or soak any dis - pense gun in any type of solvent.
14 GC-1402E 4. Place PTFE washers, p/n: 23721-04 on top and bottom of uid valve, p/n: 23743-00. 1. Ensure bores are clean before building material valves. 2. Insert bearing, p/n: 23768-01 into gun body . 3. Insert seal, p/n: 23763-00 into gun body .
15 GC-1402E Dispense T ip Reference Chart Part Number Orice 23047-J1 .012 J2 .014 J3 .022 M1 .012 M2 .014 M3 .022 N1 .012 N2 .014 N3 .022 P1 .012 P2 .014 P3 .022 Note: Use p/n: LP A2-120G and p/n: LP A2-121G when using LP A2-147-XXXX and 23047-XX series spray tips.
16 GC-1402E Dispense T ip Reference Chart Part Number Orice LP A2-147-1525 0.015 1540 0.015 1550 0.015 1565 0.015 1825 0.018 1840 0.018 1850 0.018 1865 0.018 2125 0.021 2140 0.021 2150 0.021 2165 0.021 2325 0.023 2340 0.023 2350 0.023 2365 0.023 2625 0.
17 GC-1402E Part Number Orice Min. Width (in.) Max. Width (in.) Min. Output (lbs.) Max Output (lbs.) 23005- C4 0.040 7 16.5 5.4 10.02 C5 0.050 8.5 15.5 6.36 12.23 C6 0.060 7 17 7.31 1 1.01 C7 0.070 7 13 8.53 10.58 C8 0.080 10 12.5 10.28 13.03 C9 0.
18 GC-1402E T echnical Data Category Data Maximum Fluid Working Pressure 2000 psi (14 MPa, 138 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar) T ypical Flow Rate of Pattern Guns Dependent of spray tip Maximum Fluid temperature 100° F (38° C) T rigger Air 1/4in.
19 GC -1402E Notes.
Graco Ohio Standard W arranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.
An important point after buying a device Graco Inc. GC-1402F (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco Inc. GC-1402F yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco Inc. GC-1402F - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco Inc. GC-1402F you will learn all the available features of the product, as well as information on its operation. The information that you get Graco Inc. GC-1402F will certainly help you make a decision on the purchase.
If you already are a holder of Graco Inc. GC-1402F, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco Inc. GC-1402F.
However, one of the most important roles played by the user manual is to help in solving problems with Graco Inc. GC-1402F. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco Inc. GC-1402F along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
