Instruction/ maintenance manual of the product 800-100 Graco Inc.
Go to page of 11
Rev. c ORACO SUPERSEDES 8 This manual mniains IMPCIRTYNT WARNINGS and INSTRUCTIONS FIEAD AND RETAIN FOR REFERENCE MODEL 800-100 SERIES "A" 2150 psi (150 bad OPERATING PRESSURE 2250 psi 1155 bar1 MAXIMUM WORKING PRESSURE GRACQ INC. P.Q. Box 1441 MINNEAPOLIS.
Read and Linderstand all ii;sir!.lcticn rcanui:/s before operating equipment. 1 N j E CT 1 3 N {+ fi 2 A 3 9 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ penetrate the skin and cause extremely serious injury, Fluids under high pressure from spray or leaks can including the need for amputation.
the unit. Refer to the engine instruction booklet provided with Install Wheels and Handle axle and secure with the 1/2 inch locknuts provided. Slide the axle into the frame.
Startup Before startino. be sure to read the safetv warninos and setup instruct7ons. Check the oil and gasoline levels daily I Turn on the water supply. Trigger the gun to release any back pressure ltVA 8 I?] I ihl G or triaaered oosition. Set the choke and open the fuel valve.
IOUBLESHOOTING PROBLEM Engine Will Not Start 3r Hard To Start. ingine Misses Or Lacks ’ower -ow Pressure ’ump runs extremely rough, ~ressure low. Nater leakage from under he manifold. Nater in pump crankcase. CAUSE carburetor. No gasoline in fuel tank or Water in gasoline or old fuel.
PROBLEM Frequent or premature failur of the packing. Strong surging at the inlet discharge side. and low pressure on the CAUSE Scored plungers. Over pressure to inlet manifold. Damaged or worn plungers. Abrasive material in the fluid be ing pumped. Excessive pressure and/or temperature of fluid being pumped.
Photo 4. Plungers 1) Using an M11 wrench, remove 2) Slide out the seal retainer with the plunger retainer. oil wick and rubber barrier 31 With a slight twisting motion, slinger. loosen the plunger from the plunger rod and remove NOTE: The stud may remain with the retainer when removed.
65.
SERVICE TOOLS KEY WRENCH 801-M4 EXTRACTOR TOOL 801-205 PARTS LIST REF PART NO 3 1 4 5 7 6 8 9 10 11 13 12 15 14 16 17 18 20 19 21 22 23 24 25 26 27 28 29 30 31 33 32 34 35 36 37 39 33 41 40 42 NO.
19 28 f3 14 5 A 15 L19 REF PART DESCRIPTION QTY Repair Kit 801-083 NO. NO. Includes items A, 6, C. D, E and F (15 ml lg 1 SERVICE include items 3-16) 1 1. Remove the 8 screws from the body halves (3) and 3 801-244 . HANDLE, left 1 (4). See the Parts Drawing.
CHECK VALVE 801-133 CHEMICAL INJECTOR KIT 800-102 supply. Install upstream from pump. Prevent back up of contaminated water into fresh from pump. For injecting harsh cleaning chemicals downstream WATER SANDBLASTER 8W-103 For abrasive cleaning of stubborn dirt and paint TECHNICAL DATA ENGINE: HONDA MODEL G4000B6 4 cycle.
An important point after buying a device Graco Inc. 800-100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco Inc. 800-100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco Inc. 800-100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco Inc. 800-100 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco Inc. 800-100 will certainly help you make a decision on the purchase.
If you already are a holder of Graco Inc. 800-100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco Inc. 800-100.
However, one of the most important roles played by the user manual is to help in solving problems with Graco Inc. 800-100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco Inc. 800-100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
