Instruction/ maintenance manual of the product 311767B Graco Inc.
Go to page of 16
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. is r egistered to I. S. EN ISO 9001 311767B Operation Interior T exture Spra yer RT X 6 5 0 For W ater- Based Materials Only Model 254973: 50 psi (3.
Warnings 2 Wa r n i n g s The f ollowing are gener al warnings related to the set up , use, grounding, ma intenance and repa ir of this equipment. Additional, mo re specific warnings ma y be f ound through out the bo dy of this manual where ap plicable .
Warnings 3 Electric Shoc k Hazard T o reduce the risk of electric shock: • Be sure spr a y er is adequately g rounded through electrical outlet . • Use only 3-wire, e xtension c ords. • Mak e sure grou nd prongs are intact on spr ay er and e xtension cords.
Warnings 4 CA UTION W ate r or mater ial r emaining in unit when te mperatures a re below freezing can damag e motor and/or dela y pump star tup . T o insure water and material are completely dr ained out of unit: 1. Remov e material line from spra yer .
Component Identification 5 Component Identification 3.5 cfm@40 min. Q M A K E B P J D C H G ti8369a F L N R Item Component Item Compone nt A Pump Hose Outle t J Bur p Guard B RotoFlex™ II Pump (insi.
Preparation 6 Preparation Pressure Relief Procedure T o reduce r isk of injury , f o llow this procedur e whene ver y ou see this symbol throughout this manual, Also , perform this procedure whe ne v er you : • Stop spra ying • Check or repair any par t of this syst em • Install or clean spra y nozzle 1.
Setup 7 Setup T exture Spra ying 1. Connect air hose to user-su pplied air compressor & mater ial hose ( G) to mate rial hose outlet s. 2. Connect use r supplied a ir hose to gun. 3. Open air valv e. 4. Connect material hose to gun. 5. Install spra y nozzle.
Setup 8 8. P oint gun into waste buc ket and pull tr igger to pu mp water t hrough the system. Cont inue to trigger gun until material hopper is empty . 9. Install bur p guard (J). Caution , page 3. 10. Add pre-mixed texture mix to mater ial ho pper .
Mixing Material 9 Mixing Material Dry Mix - 40 lb (18 kg) ba g. 1. Slo wly add one 40 l b. (18 kg) bag of te xture material to 5-6 gallons (18.9- 22.7 liters) of cle an water as instructed on the bag instructions . 2. Agitate to mix, using a ha lf-inch, variable speed drill with mixing paddle , to a smooth, lum p-free consistency .
Spray Techniques 10 Spra y T echniques Recommended Nozzle Selection Char t 1 Control air v olume with gun air v alve . 2 F or more material v olume tr y a larger nozzle. Adjusting the System Sufficient fluid ou tput (v olume and pressure) and good atomization is a balance of atomizin g air , material thickne ss/material flow an d nozzle selection.
Shutdown and Cleanup 11 Shutdo wn and Cleanup T exture Spra ying (5 gallon Material Hopper) When you hav e finished spra y ing: 1. T ur n spra yer power switch (K) ON (air co mpressor can remain OFF) . 2. Close gun air v alve . 3. T rigger gun into buc ket until most of te xture mix is pumped out.
Troubleshooti ng 12 T r oubleshooting Prob lem C ause Solution Spra yer won’t r un P ower s witch not o n T ur n s wit ch on. No pow er at wall outle t Chec k outlet by plugging in another appliance . If appliance does not work, try another outlet. Wrong size ge nerator Use a 3500 wa tt or larger gener ator .
Troubleshooting 13 Speed of a pplication slow or slower New pump ho se not broken in properly Run pump d r y for no more than 2 minutes. Material too thic k Thin material. Nozzle too small Change nozzles to a larger siz e. See Recommended Nozzle Selection Char t, page 10.
Technical Data 14 Te c h n i c a l D a t a Main Unit Po wer Re quirement s . . . . . . . . . . . . . . . . . . . . 120 V a c, 60 Hz, 15A, 1 p hase Maximum Fluid Working Pre ssure . . . . . . . . . . . . . . . . . . 50 psi, (3.5 bar ) Maximum Air Working P ressure .
Notes 15 Notes.
Graco Warrant y 16 Graco W arranty Graco warrants all equipment ref erenced in this document which is manufactured by Gr aco and bearing its name to be free from de fe c ts i n material and workmanship on the date of sale to the origin al purch aser for use.
An important point after buying a device Graco Inc. 311767B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco Inc. 311767B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco Inc. 311767B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco Inc. 311767B you will learn all the available features of the product, as well as information on its operation. The information that you get Graco Inc. 311767B will certainly help you make a decision on the purchase.
If you already are a holder of Graco Inc. 311767B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco Inc. 311767B.
However, one of the most important roles played by the user manual is to help in solving problems with Graco Inc. 311767B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco Inc. 311767B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
