Instruction/ maintenance manual of the product 1500 SFDE American Aldes
Go to page of 16
AL-04 9806 aav#1534 For Models: HRV 1500 IFD HRV 1500 EFD AAV1534 OPERA TION AND INST ALLA TION MANUAL NOTE: ALTHOUGH SOME MODELS DIFFER IN OPERATION, THE BASIC INSTALLATION STEPS ARE SIMILAR.
GENERAL This Heat Recovery V entilator (HR V) is designed to provide fresh air into the building while exhaust- ing an equal amount of stale air . During the winter months, the incoming cold fresh air is warmed by utilizing the heat recovered from the stale air be- fore it is exhausted to the outdoors.
SPECIFICA TIONS AIRFLOW 1500cfm (705 L/s) at 1.0”wg ESP . PERFORMANCE 65% effective at 1500 cfm (705 L/s). CORES Six patented aluminum heat recovery cores arranged for efficient cross-flow ventilation. MOTORS T wo single shaft ECM variable speed, 208/240V , 9.
4 Engineering Data Model HRV 1500 SFDE SPECIFICA TIONS AIRFLOW 1500cfm (705 L/s) at 1.0”wg ESP . PERFORMANCE 65% effective at 1500 cfm (705 L/s). CORES Six patented aluminum heat recovery cores arranged for efficient cross-flow ventilation. MOTORS T wo single shaft ECM variable speed, 208/240V , 9.
Function & Controls Model(s) HRV 1500 SFD / SFDE 5 Basic Functions Speed control is obtained by powering 24V to one of the designated speed taps. Example: A jumper between the R terminal and the G terminal will result in low speed operation.
6 HRV 1500 SFD or SFDE Speed Selection The HRV 1500 SFD and HRV 1500 SFDE are equipped with ECM motors that can be programmed to maintain various different airflows. The HRV 1500 SFD and HRV 1500 SFDE have three selectable speeds (High medium and low).
Servicing 7 The HRV 1500 SFD and HRV 1500 SFDE are designed to be serviceable from either side. If access to the unit will only be available from one side, the unit must be set up accord- ingly . The unit is factory shipped to be serviced from the front.
8 Option 1 Unit can be suspended with “U” channels and Threaded Rod Mounting the 1500 Option 2 Unit can be placed on blocks (sleepers).
9 Frame Assembly 1. T ake one end piece (locking tabs) and one side piece (slots). Stand both pieces vertically on the floor or roof. See Figure 1. 2. Raise slightly the corner of the end piece (locking tabs) and mate with side piece (slots), ensuring that lower lock- ing tab with leading edge is through slot opening.
10 Roof Curb Detail for Model HRV 1500 SFDE.
11 Ducting - General Drains Connect the drain pans in the bottom of the HR V to a drain line fastened to the holes provided. Create a “P” trap to prevent odors from being drawn through. Make sure the drain line slopes down to drain properly and if this is not possible a condensate pump will be required for removal of the water .
12 Ducting - Distribution Stale Air Return System The stale air return system is used to draw air from the points in the building where the worst air quality problems occur .
13 The Integrated HV AC System W ARNING: This unit is a quiet, efficient, low pres- sure system. Special care and attention should be given if connecting this unit to any other air han- dler that may draw more air than this unit is de- signed to accommodate.
14 Pilot T ube Air Flow Balancing - Commercial It is necessary to have balanced air flows in an HRV . The volume of air brought in from the outside must equal the volume of air exhausted by the unit.
15 Wiring Diagram.
AMERICAN ALDES VENTILATION CORPORATION warrants to the original purchaser of the Com- mercial ALDES HRV model and accessories referred to below, to be free from manufacturing defects.
An important point after buying a device American Aldes 1500 SFDE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Aldes 1500 SFDE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Aldes 1500 SFDE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Aldes 1500 SFDE you will learn all the available features of the product, as well as information on its operation. The information that you get American Aldes 1500 SFDE will certainly help you make a decision on the purchase.
If you already are a holder of American Aldes 1500 SFDE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Aldes 1500 SFDE.
However, one of the most important roles played by the user manual is to help in solving problems with American Aldes 1500 SFDE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Aldes 1500 SFDE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
