Instruction/ maintenance manual of the product RT700 Godex
Go to page of 52
1 RT700/RT730 BARCODE PRINTER USER MANUAL User Manual Version Issue Date P/N : RT700 series : Rev. 1.4 : 2013.10.03 : 920-014711-00.
Contents Contents RT700/RT730 USER MANUAL CONTENTS 1 Barcode Printer 001 1.1 1.2 Box Content Getting to Know Your Printer 001 002 2 Printer Setup 006 2.
Declaration Declaration RT700i/RT730i USER MANUAL FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules.
Safety instructions Safety instructions RT700/RT730 USER MANUAL SAFETY INSTRUCTIONS Please read the following instructions carefully. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source.
1 1 Barcode Printer 1.1 Box Content Please check that all of the following items are included with your printer. 001 USB Cable RT700/RT730 Barcode Printer CD Including GoLabel software and RT700/RT730 user manual. Label Stock Ribbon Module Empty Ribbon Core Ribbon Ribbon Hubs Set of 2.
2 Front View 1 Barcode Printer 1.2 Getting to Know Your Printer 002 Device Overview Rear View ETHERNET PORT SERIAL PORT FAN-FOLD LABEL INSERT Feed slot for continuous labels POWER JACK USB POR.
3 Bottom View 1 Barcode Printer 003 COVER OF THE MODULE CONNECTION JACKS * *** Cut-outs are not intended for wall-mount use..
4 1 Barcode Printer The Internal View of Printer 004 RELEASE CATCH Release catch for closing the printer cover LABEL SENSOR MODULE GUIDE TRACK LABEL SENSOR PLATEN MODULE PLATEN PLATEN LOCKERS LABEL SU.
5 1 Barcode Printer 005 The Printing Mechanism RIBBON REWIND MECHANISM COVER The cover for Ribbon rewind mechanism NOTCH OF RIBBON REWIND WHEEL RIBBON REWIND WHEEL PRINT HEAD RIBBON SUPPLY MECHANISM N.
6 2 Printer Setup 2.1 Open the Printer Open the Printer Cover and the Printing Mechanism Place the printer on a flat surface. Open the printer cover by pulling the cover release catches on both sides of the printer and lift the printer cover.
7 2 Printer Setup 2.2 Loading the Ribbon 007 A New Ribbon Module Installation 1. Attach the ribbon to the empty ribbon core with the adhesive strip at the end of the ribbon. 2. Insert the ribbon hub into empty ribbon core and new ribbon. Wind the ribbon around the empty ribbon core for 2 to 3 circles.
8 2 Printer Setup 008 Load the Ribbon on the Printer For Ribbon Supply Module RIBBON SUPPLY MECHANISM NOTCH OF RIBBON SUPPLY WHEEL RIBBON SUPPLY WHEEL Place RIBBON SUPPLY MODULE 1. Place the ribbon supply module into the printing mechanism. Please the left-hand side of ribbon hub first.
9 2 Printer Setup 009 2. Unlock the release catch to close the printer cover. Push the release catch forward to unlock it. The ribbon supply module loading is completed.
10 2 Printer Setup 010 1. Open the cover of ribbon rewind mechanism. 2. Place the ribbon rewind module into the ribbon rewind mechanism. Please the left-hand side of ribbon hub first. Make sure the holder of ribbon hub is inserted into the notch. Then place the right-hand side of ribbon hub.
11 2 Printer Setup 011 3. Turn the ribbon rewind wheel to tighten the ribbon until it has no wrinkles. 4. Close the cover of ribbon rewind mechanism. The ribbon loading is completed once the ribbon supply module and ribbon rewind module are assembled correctly.
12 2 Printer Setup 2.3 Loading the Label Roll Module 012 Loading the Label Stock on the Printer LABEL STOCK LABEL SUPPLY MODULE RELEASE CATCH Release catch for opening the label supply hub LABEL SUPPLY HUB Set of 2 LABEL GUIDE Set of 2 LABEL GUIDE PLATE Set of 2 1.
13 2 Printer Setup 013 3. Feed the Label through the label guides. The label guides will help to prevent the label swaying. Through the label guides LABEL GUIDE Set of 2 4. Unlock the release catch to close the printer cover. 5. Press the FEED key and make sure the label is fed smoothly.
14 2 Printer Setup 2.4 Connecting the Printer to the Host Computer 014 1. Please make sure that the printer is switched off. 2. Connect the power cord to the AC adapter. AC ADAPTER POWER CORD Connect the jack of the power adapter to the printer and connect the plug of the power adapter to the socket of the wall.
15 2 Printer Setup 015 3. Connect the USB/serial cable to the printer and host computer. 4. Pressing the power button. The power LED indicator should now lights up.
16 2 Printer Setup 2.5 Installing Printer Driver and GoLabel with Super Wizard CD 016 * *** If the Super Wizard program did not run automatically, you can either turn on the “Auto-run” setting for your CD/DVD driver or double-click the icon of CD/DVD driver to run the program.
17 2 Printer Setup 017 4. As the printer driver and GoLabel are installing, a screen will display a progress bar. * *** If you need more resources, tools or reference documents, you can also find them on Super Wizard CD. Just click “Other Choices” on Welcome Screen to access the files.
18 2 Printer Setup 018 1. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD. Select the icon for the driver file and click it to start the installation. 2. Follow the instructions on the screen.
19 2 Printer Setup 019 4. Specify the port used to connect the printer to the host computer. 6. Once the installation is complete, a summary of the printer settings is displayed. Check whether the printer settings are correct and click "Finish" to start copying the driver files.
20 2 Printer Setup 020 7. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder. Godex RT700i Godex RT700i.
21 3 Printer Setting and Control 3.1 Operation Panel 021 FEED Button When you press the FEED button, the printer moves the label to the defined stop position. If you are using continuous labels, pressing the FEED button will move label stock until you release the button again.
22 3 Printer Setting and Control 3.2 Label Calibration and Self Test 022 Label Calibration The printer can automatically detect and store label height. That means the host computer does not need to transmit the label height to the printer. Self Test Self-test function lets you check whether the printer is functioning normally.
23 3 Printer Setting and Control 023 Label Calibration Button Keep pressing calibration button for 1 second, the printer can immediately run the label size calibration. Press CALIBRATION BUTTON Calibration button can be used to find correct printing position or eliminate the “Media Error” problem.
24 3 Printer Setting and Control 3.3 Error Alerts 024 In the event of a problem that prevents normal functioning of the printer, you will see an error message on LED indicators and hear some beep signals. Please refer to below table for the error alerts.
25 4 NetSetting for Ethernet 4.1 Installing the NetSetting software 037 The NetSetting software is used to manage the network configurations when connecting the printer via Ethernet port. It is available on product CD or can be downloaded from official website.
26 4 NetSetting for Ethernet 4.2 The Interface of NetSetting 026 Click the NetSetting icon to start the program; you will see the start page as below. The start page will display the basic information of connected printer and your PC. There are six tabs on the top of interface which can configure different types of network settings.
27 4 NetSetting for Ethernet 027 * *** To fully benefit from the NetSetting software, you should be familiar with basic networking principles. Please contact your network administrator for related network setting information. You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.
28 4 NetSetting for Ethernet 028 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Alert Path Setting NetSetting will send the alert messages to designated mail account when the error happened on printer.
29 4 NetSetting for Ethernet 029 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Alert Message Setting For the alert message notification function, you can decide which error cases need to be sent out to the operator.
30 4 NetSetting for Ethernet 030 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Printer Configuration Set or change the configurations of connected printer. Most of key settings for the printer operation can be done by this setting page.
31 4 NetSetting for Ethernet 031 You can press “Send Command” button to send printer commands via Ethernet port and control the printer remotely. User Command The “User Command” tab provides a communication interface for operator to control the printer.
32 BOOT : 1.000a1 F/W : ZX1200 1.000a 4 NetSetting for Ethernet 032 In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer configurations back to factory default. Firmware Download On “Firmware Download” tab, the current version of printer firmware will be showed on the screen.
33 5 Accessories 045 Before installing the optional modules, please make some preparations as follows. 1. Turn off the printer : Remember to switch off the printer before installing any module.
34 5 Accessories 046 4. Remove the platen : Lift up the release clips on both sides of the platen to release and pull upward the platen. CLIP Release the clip 5. Ribbon loading : Please see the Section 2.2 for further information about Loading the Ribbon.
35 5 Accessories 5.2 Installing the Label Dispenser 047 The Overview of the Label Dispenser * *** A label liner thickness of 0.006 mm ± 10% and a weight of 65 g/m 2 ± 6% are recommended. ** ** The label dispenser will take labels up to a max. width of 118 mm.
36 5 Accessories 048 2. Place label dispenser to align both holes of screw and then tighten the screws. 3. Place the platen back to the printer and lock the clips. 4. Close the printer cover and printing mechanism. Then to turn the printer upside down.
37 5 Accessories 049 5. Open the cover on the bottom of printer. 6. Plug the connector fo the label dispenser to the jack. 7. Close the cover of the module connection jacks.
38 5 Accessories 050 2. Feed the Label stock through the label guides. And pull the label liner through the platen and the steel of the label dispenser. * *** Labels should be at least 25 mm high. Loading Label Roll with the Label Dispenser Module 1. Remove the first label from the label stock.
39 5 Accessories 051 3. The feeding path of label and liner should be as shown in below graphic. 4. Close the label dispenser and printer cover. The installation is completed now.
40 5 Accessories 052 5. Press the FEED button to feed the label. The label will be peeled from the liner while it passes through the label dispenser. RT700i Press the feed key LABEL LINER LABEL * *** There is a paper sensor on the Label Dispenser module.
41 5 Accessories 5.3 Installing the Cutter 041 The Overview of the Cutter * *** Remember to switch off the printer before installing the cutter. ** ** Do not use to cut adhesive labels! Glue residue will be left on the cutter blade and impair its functioning.
42 5 Accessories 054 2. Place the cutter to align both holes of screw and then tighten the screws. 3. Place the platen back to the printer and lock the clips. Tighten the screw Lock the clip CLIP 4. Close the printer cover and printing mechanism. Then to turn the printer upside down.
43 5 Accessories 055 5. Open the cover on the bottom of printer. 6. Plug the connector for the cutter to the jack. 7. Close the cover of the module connection jacks. * *** The printer must be switched off, or the motherboard may be destroyed! ** ** There are 2 jacks : the lower jack for the label dispenser, the upper jack for the cutter.
44 5 Accessories 044 2. Close the top cover and printing mechanism. To finish, press the FEED button to set the label position. * *** We advise against using inside wound label stock. ** ** Labels should be at least 30 mm high. When using the printer with the cutter, you should set the stop position (^E) to 30.
45 6 Maintenance and Adjustment 6.1 Cleaning the Print Head 057 Dirt on the print head or ribbon, or glue residue from the label stock may result in inadequate print quality.
46 6 Maintenance and Adjustment 6.2 Troubleshooting 058 * *** If any problems occur that are not described here, please contact your dealer. Problem Solution The printer is s wi tched o n but the LED does not light up. ♦ Check the power supp ly. Please se e the Section 2.
Appendix PRODUCT SPECIFICATIONS RT700/RT730 USER MANUAL APPENDIX.
Appendix Appendix INTERFACE RT700/RT730 USER MANUAL APPENDIX Pinout Description Connector Type : Type B Serial Port Default settings ： Baud rate 9600, no parity, 8 data bits, 1 stop bit, XON/XOFF pr.
An important point after buying a device Godex RT700 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Godex RT700 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Godex RT700 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Godex RT700 you will learn all the available features of the product, as well as information on its operation. The information that you get Godex RT700 will certainly help you make a decision on the purchase.
If you already are a holder of Godex RT700, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Godex RT700.
However, one of the most important roles played by the user manual is to help in solving problems with Godex RT700. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Godex RT700 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
