Instruction/ maintenance manual of the product AC40L Global Machinery Company
Go to page of 16
AC24L/A C40L 030505 AC24/40L Ed5 INSTRUCTION MANU AL 2HP & 2-1/2HP 24 Litre & 40 Litre Air Compressors • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • Paris W arning! Do not switch on for the first time without first filling with oil.
Contents W arr anty 2 W arning labels e xplained 3 Introduction 4 Environment al protection 4 Description of s ymbols 4 Specifications 4 General safety instructions 5 Additional safety rules f or air .
W arning labels explained On the tank of your air compressor you will notice various warnings about the operation of the compressor . These warnings and the procedures associated with them are explained fully in this manual on the f ollowing pages. Please take note o f these.
Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . Wear hearing protection. Wear eye protection. Wear breathing protection. Conforms to relevant standards f or electromagnetic compatibility.
General safety instructions T o use this tool properly , you must observe the safety regulations, the assembly instructions and the operating instructions to be found in this Manual. All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards.
17. Stay alert. Watch what you are doing. Use common sense . Do not operate a power tool when you are tired. 18. Check f or damaged parts. Before using a tool, check that there are no damaged parts. If a part is slightly damaged, carefully determine if it will operate properly and perform its intended function.
paint or other materials to be sprayed. Closely follow all safety instructions. Use a respirator mask if there is a chance that you might otherwise inhale the spray material. Carefully check the effectiveness of any respirator mask you intend using. • Always wear safety goggles or glasses when using the air compressor .
W arning. In the event that an air line is cut or broken, the air supply must be turned off at the compressor . A broken air line which is not supported is extremely dangerous and can whip around very quickly , both with the capability of striking people , and blowing foreign particles into the air .
Know y our product 1. Handle 2. Pressure switch cover 3. On/off switch 4. Direct outlet valve 5. Direct outlet pressure gauge 6. Regulating knob 7. Regulated outlet valve 8. Regulated outlet pressure gauge 9. Safety valve 10. Non-return valve 11. Drain cock 12.
Unpacking Due to modern mass production techniques, it is unlik ely that your GMC Power T ool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
W arning. The air filter must be added before first use . Failure to fit the air filter will damage the compressor and will void the warranty. 4. Remove the plastic air filter plug from the head of the compressor . 5. Carefully screw the air filter assembly (16) into the threaded hole taking care not to cross the thread.
Operation 1. The pressure in the tank is controlled by the action of the pressure switch located under the pressure switch cover (2). When the set maximum pressure is reached the pressure switch activates and the motor is switched off.
13 Tr oubleshooting Tr ouble Motor will not run, running too slow or becoming ex cessively hot Main compressor sticking/tight Vibration or abnormal noise Possible cause 1. Power f ault or supply voltage too low 2. Power cord too long or too thin 3. Faulty pressure switch 4.
Maintenance 1. After the first 10 hours of working, empty the crank case of oil and refill with clean oil by removing the crank case oil plug (left hand side of the crank case at the bottom) Note . Use good quality compressor lubricating oil. • SAE30 or L-DAB 100 over 10°C • SAE10 or L-DAB 68 under 10°C 2.
General inspection 1. Regularly check that all the fixing screws are tight. 2. The supply cord of the tool should be check ed frequently for damage . If damaged, have the cordset replaced by an authorised service facility to avoid a hazard. Cleaning 1.
Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New.
An important point after buying a device Global Machinery Company AC40L (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Global Machinery Company AC40L yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Global Machinery Company AC40L - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Global Machinery Company AC40L you will learn all the available features of the product, as well as information on its operation. The information that you get Global Machinery Company AC40L will certainly help you make a decision on the purchase.
If you already are a holder of Global Machinery Company AC40L, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Global Machinery Company AC40L.
However, one of the most important roles played by the user manual is to help in solving problems with Global Machinery Company AC40L. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Global Machinery Company AC40L along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
