Instruction/ maintenance manual of the product 1050W Global Machinery Company
Go to page of 14
PRT ABLE 031219 ED12 DR INSTRUCTION MANU AL 1050W Pow ered Router T able • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • P aris.
Contents.
Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . W ear hearing protection. W ear eye protection. W ear breathing protection. Double insulated f or additional protection.
General safety instructions The tool must be used only for its prescribed purpose . Any use other than those mentioned in this Manual will be considered a case of misuse . The user and not the manufacturer shall be liable f or any damage or injury resulting from such cases of misuse .
15. A void unintentional starting. Always check that the switch is in the OFF position before plugging in the tool to the power supply. Do not carry a plugged in tool with your finger on the switch. 16. Stay alert. W atch what you are doing. Use common sense .
• Before using the tool to make a cut, switch on and let it run for a while . Watch for vibration or wobbling that could indicate an improperly installed bit.
Know y our product 1. T able 2. Rear fence 3. Infeed fence 4. Outfeed fence 5. Fence locking knobs 6. Guide block locking knobs 7. Dust extraction hood 8. Dust extraction port 9. On/Off switch 10. Mitre gauge 11. Mitre gauge locking knob 12. Spindle lock lever 13.
Installing and r emoving collets W arning. Always ensure the tool is switched off and the plug is removed from the power point before making any adjustments. When changing the collets or when changing bits, the height of the motor assembly should be raised to close to the maximum height to gain full access to the collet nut.
11. Replace the collet assembly cover in the following way: 11. The collet assembly cover locates in the centre of the height adjusting ring and is secured in place with two small screws.
Ad justments A djusting the speed 1. Adjust the variable speed dial (9) to suit different material. The tool cuts quicker and smoother at different speeds and when working in different woods or in plastic or aluminium. 2. Adjust the variable speed dial to a higher number for f aster speed or to a lower number for slower speed.
A djusting the fence for trimming 1. When trimming timber the material coming out on the left hand side (outfeed) (4) of the cutter will be thinner than the material being fed through on the right hand side (infeed) (3). 2. The left hand guide block will need to be adjusted to compensate for the thinner material.
A djusting the mitre gauge 1. The mitre gauge (10) slides horizontally along the table to allow for edging and mitre cuts in the work piece . 2. T o adjust the mitre gauge to the desired angle loosen the mitre gauge locking knob (11) and rotate the mitre gauge to the desired angle from 0° to 45°.
Operation 1. Insert and secure the router bit. 2. Adjust the speed, depth o f cut, feather boards, fence alignment and mitre gauge as required. 3. Ensure you adjust the infeed fence (3) so that it supports the uncut material and the outfeed fence (4) so that it supports the cut material, compensating for the removed material if trimming.
Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New.
An important point after buying a device Global Machinery Company 1050W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Global Machinery Company 1050W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Global Machinery Company 1050W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Global Machinery Company 1050W you will learn all the available features of the product, as well as information on its operation. The information that you get Global Machinery Company 1050W will certainly help you make a decision on the purchase.
If you already are a holder of Global Machinery Company 1050W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Global Machinery Company 1050W.
However, one of the most important roles played by the user manual is to help in solving problems with Global Machinery Company 1050W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Global Machinery Company 1050W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
