Instruction/ maintenance manual of the product GA-EX38-DQ6 Gigabyte
Go to page of 13
A. T eaming Part a. Cr eate T eaming Flow (i) From the start up menu, left click the icon in Program s Æ Realtek T eaming and VLAN Æ Realtek T eaming and VLAN Utility , as shown in the figure below:.
(iii) T eaming needs to set th ree parts 1. select adapters (at least two adpaters) 2. select teaming mode There are three teaming modes for user choosing. (Default = 802.3ad) (1) General Switch Mode This mode is supported to general switch (without teaming function swtich).
3. after selecting teaming adapter and team ing mode, click teaming button (iv) If the T eaming created completely , the Dialog will show “Create V irtual Adapter For T eaming Complete” and click OK.
(vi) Network Component has a new V irtual Adapter For T eaming b. T eaming Notes (i) The gigabit switch pr efer supporting teaming function (likely FEC/ GEC, LACP…) If the gigabit switch doesn’t support team ing function, the performance of Inbound T raffic (Rx) will only have one adapter performance.
FEC/GEC and the mode of the teaming sw itch is LACP , the teaming switch will send LACP packets to the teaming server and wait the response form the teaming server . But the teaming server will not reply the team ing switc h due to set FEC/GEC mode. So, the teaming is failed.
(ii) If the Vlan removed completely , the Dialog shows “Rem ove T eaming V irtual Adapter Finnished” and click OK..
B. Vlan Part a. Cr eate Vlan Flow (i) From the start up menu, left click the icon in Program s Æ Realtek T eaming and VLAN Æ Realtek T eaming and VLAN Utility , as shown in the figure below: (ii) Th.
(iii) Click to select one adapter for Vlan (one adapter selected) (iv) Click the Vlan button and start to create Vlan.
(v) If the Vlan created com pletely , the Dialog w ill show “Create V irtual Adapter For Vlan Complete” and click OK. (vi) Network Component has a new V irtual Adapter For Vla n.
(vii) Select the virtual Adapter and ri ght-click to select “Properties” (viii) The below figure is showed the propertie s. T here, click the “Configure “Button to setup the value of Vlan ID.
(ix) Select Advanced Page and Click Vlan ID properties to setup the value..
b. Remove Vlan Flow (i) If without closing the user interf ace, directly click remove button. (The selected adapters don’ t care) If closing the user interface and reopen it, directly click remove b.
(ii) If the Vlan removed completely , the Dialog shows “Rem ove VLAN V irtual Adapter Finnished” and click OK..
An important point after buying a device Gigabyte GA-EX38-DQ6 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Gigabyte GA-EX38-DQ6 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Gigabyte GA-EX38-DQ6 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Gigabyte GA-EX38-DQ6 you will learn all the available features of the product, as well as information on its operation. The information that you get Gigabyte GA-EX38-DQ6 will certainly help you make a decision on the purchase.
If you already are a holder of Gigabyte GA-EX38-DQ6, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Gigabyte GA-EX38-DQ6.
However, one of the most important roles played by the user manual is to help in solving problems with Gigabyte GA-EX38-DQ6. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Gigabyte GA-EX38-DQ6 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
