Instruction/ maintenance manual of the product 2040L Genie
Go to page of 16
F or H elp , c all 1-800-35-GENIE or visit www .geniecompany .com ® C OMPLETE WITH I NTELLIC ODE R EMO TE C ONTROL AND SERIES II E LECTR ONICS F or up t o 7’ 6” tall Doors. Included W all Control MUST be installed prior to Operation of this Garage Door Opera tor .
INCL UDED IN THIS P A CK AGE · W arranty Inf ormation · Pr e Installation Check list to be reviewed prior to an y assembly or installation · Pictorial and step by step opener assembly instructions .
F or H elp , c all 1-800-35-GENIE or visit www .geniecompany .com 3 3 Garage Doors are heavy objects that move with the help of springs under high tension and electric motors.
F igur e 2 N ote Door T ype SECTIONA L D OOR, TORSION SPRINGS SECTIONA L D OOR, EXTENSION SPRINGS ONE-PIECE DOOR, TRACKLESS 4 For Help , call 1-800-35-GENIE or visit www .geniecompany .com M EASURE G ARAGE D OOR H EIGHT A The Belt Drive Garage Door Opener is designed for doors up to and including 7’ 6” tall.
F or H elp , c all 1-800-35-GENIE or visit www .geniecompany .com 5 • Mark a point at center of door and on header directly above door . Draw a cent er line to connect points. B F ind Header Bracket mounting height ( F igure 4 ): (Do not attach Header Bracket).
6 For Help , call 1-800-35-GENIE or visit www .geniecompany .com S our c e S ensor Safe-T-Beam® Mounting Bracket T op of B r ack et 6" ab ove floor Figur e 7 Mounting Safe-T-Beam® Components F igur e 8 R ecommended T ools Go to Assembly and Installation P oster for full Installation Instructions.
F or H elp , c all 1-800-35-GENIE or visit www .geniecompany .com 7 A LIGNING T HE S AFET Y -T-B EAMS ® Figur e 1 SAFE-T-Beam® F igur e 2 Indic a t or Ligh ts NO TE The Safe-T-Beam® is an in visible ray of light that tra vels across the bottom of the garage door opening ( F igure 1 ).
8 For Help , call 1-800-35-GENIE or visit www .geniecompany .com P ROGRAMMING R EMO TE C ONTROLS Figur e 1 Learn C ode Button and Indicator Light M AINTENANCE AND A DJUSTMENTS Step 2: W ARNING A moving garage door ma y cause ser ious injur y or death.
F or H elp , c all 1-800-35-GENIE or visit www .geniecompany .com 9 NO TE • E ach R emot e C on tr ol must be programmed separat ely . • The Remote Con trols will not cause the door Opener to close the garage door if the Safe-T-Beam® System is malfunctioning .
10 For Help , call 1-800-35-GENIE or visit www .geniecompany .com A DJUSTING THE O PEN AND C L OSE L IMIT S F igur e 2 Examine where the carriage stops Step 3: D Adjust the open limit ( F igure 3A ). • T urn the Open Limit Adjustment Screw 1/4 turn at a time toward the up or do wn to change where the bullet stops.
F or H elp , c all 1-800-35-GENIE or visit www .geniecompany .com 11 Figur e 3B Adjusting the close limit E Adjust the close limit ( F igure 3B ). • T urn the Close Limit Adjustment Screw 1/4 turn at a time toward the up or do wn to change where the bullet stops.
12 For Help , call 1-800-35-GENIE or visit www .geniecompany .com NO TE D ur ing the next adjustment, if the door stops during op ening or reverses during closing befor e reaching the limits, the door forc e must be adjusted. Change the door f or c e setting as descr ibed in the next sec tion then return here to finish setting these limits.
A C heck the door ’ s balance • Close the garage door . • Disengage the door from the opener . • Raise and lower the door manually . – The door should mov e fr eely without sticking or binding. • R aise the door halfwa y open. – The door should remain relativ ely still.
14 For Help , call 1-800-35-GENIE or visit www .geniecompany .com T ROUBLESHOO TING I F THERE IS ANY TROUBLE WITH THE O PENER , TR Y THESE SOL UTIONS BEFORE C ALLING THE H ELP N UMBER . NO TE In all cases, watch the opener’ s lights for any flashing trouble codes.
T HE O PENER WILL NOT OPER A TE ` BECA USE OF A POWER F AILURE O PENER IS NOISY O PENER RUNS BY ITSELF R EMO TE C ONTROL WILL NOT OPERA TE A T A DIST ANCE FROM THE OPENER .
16 For Help , call 1-800-35-GENIE or visit www .geniecompany .com F LASHING L IGHT T ROUBLE C ODES N UMBER OF FLASHES PROBLEM CA USE REMED Y 2 FLASHES Door won ’t close Shorted wall Check wall con trol wires. Be sure both are c onnec ted to control wir e terminal screw s.
An important point after buying a device Genie 2040L (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Genie 2040L yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Genie 2040L - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Genie 2040L you will learn all the available features of the product, as well as information on its operation. The information that you get Genie 2040L will certainly help you make a decision on the purchase.
If you already are a holder of Genie 2040L, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Genie 2040L.
However, one of the most important roles played by the user manual is to help in solving problems with Genie 2040L. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Genie 2040L along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
