Instruction/ maintenance manual of the product 2022 Genie
Go to page of 29
Includes: 2-Bulb Light System W all Console Includes INTELLICODE ® Remote Control Safe-T -Beam ® System must be installed to close door . For use only with sectional doors. Homelink ® and Car2U ® compatible For Answers and Assistance: 1.800.354.3643 or visit www .
PN 37026501206 01/27/2012 2 OVER VIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMA TION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors.
3 T ABLE OF CONTENTS OPENER FEA TURES INTELLICODE ® Rolling Code Security System. An electronic rolling code system that enhances the security of the door opener by continuously changing the access code each time the remote control is used. The door opener responds to each new code only once.
6 T o avoid damage to your door and/or opener , make sure you disable and/or remove any door locks, ropes, and/or cables (NOT door lif t cables) prior to installing your opener . ( Refer to Section 1.) 4 PRE-INST ALLA TION CHECK LIST FOR HELP-1.800.354.
5 TYPICAL SECTIONAL DOOR INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM TYPICAL SUPPORT BRACKET (NOT PROVIDED) EXTENSION SPRING OR TORSION SPRING SAFE-T -BEAM ® BRACES ADDED HEADER BRACKET MOUNTING BOARD POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET 4 1 3 6 2 3 5 SECTIONAL DOOR Pg.
6 RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3/16" Drill Bit 1/4", 7/16", 3/8" and 1/2" Sockets S tep ladder Drill Ratchet Carpenter ’s level Pencil T ape measure Wire strippers Phillips screwdriver Adjustable wrench P ARTS IDENTIFICA TION - Not Shown Full Size .
F ASTENERS - Shown Full size ( See Parts List below for full description.) Lag screw - 5/16" x 2" Self-drilling Screw 1/4 -20 x 3/4" Hex Flange Nut 1/4 -20 Cotter pin Clevis pin 5/16&qu.
8 1-PIECE RAIL HARDW ARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3-PIECE RAIL HARDW ARE ASSEMBLED VIEW T ensioner Rail with chain Chain C ha in Co n ne c to r Release Knob He.
9 PENER ASSEMBL Y FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 NOTE: Three (3) piece rail assemblies are for a 7 foot high door . Clear a workspace area to unpack and organize box and contents for assembly . 1. There are 4 boxes inside the carton.
10 FIG . 1-2 Split Rail sections . A B Chain Rail Center Rail End Rail Wire Tie(s) Rail Assembly for CHAIN DRIVE OPENER NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. 3. Remove the two rail sections that are not connected to the chain and place them on floor (Fig.
POWER HEAD & RAIL ASSEMBL Y Assembly for CHAIN DRIVE OPENER NOTE: Handle carefully! Drive chain can slide out of rail. NOTE: For power head and rail assembly locate Bag 1 from Box 1. NOTE: Copy serial number from power head frame and record it on warranty page.
12 FIG . 2-2 Finding highest point of travel . OPENER INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 2 HEADER AND DOOR MOUNTING BRACKETS: 1. Finding header bracket mounting location . • Close garage door . – Use a pencil and level.
MOUNTING THE OPENER: 1. Getting st arted . • Position assembled rail on wall next to header bracket (Fig. 2-4) . – Place material on floor under power head to protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.
14 DOOR BRACKET : NOTE: For door bracket and bolts locate Bag 4 from Box 2. 1. Finding door bracket mounting location . • Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers (Fig. 2-7) .
NOTE: Wall console will not operate until limits are set. NOTE: For Wall Console, wire and insulated staples locate Bags 6 and 7 from Box 2. 1. W all Console location. • W all Console location should be in direct sight of door . • It should be at least five feet (5') above floor to prevent small children from operating door .
16 3. Securely fasten wires. • Securely fasten wires to ceiling and wall using insulated staples provided. – Use insulated staples. – S taples should be snug only . • If rear cover is attached to power head, remove it. • On power head: – Route Wall Console wires through wire guide on power head.
17 AFE-T -BEAM ® S YSTEM INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 4 r o o d e h t e s o l c t o n l l i w r e n e p o e h T : E T O N automatically unless the Safe-T -Beam ® System is installed. NOTE: For Safe-T-Beam®, screws, wire, and insulated staples locate items and Bag 8 from Box 3.
18 3b. Wiring (pre-wired) . • Route wire from wall to Safe-T -Beam ® sensors (Fig. 4-5b) . • S plice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash (striped-to- striped) and plain-to-plain (white-to-white) . - T rim sensor wire to approximately one foot (1 ft) from sensor .
19 ONNEC TING TO POWER FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 5 Plug the opener into a properly grounded electrical outlet (Fig. 5-1). • T o r e d u ce t h e r i sk o f e l e c tr i c a l s h oc k, t h i s e q u i p m e n t h a s a g ro un de d ty pe p l u g t h a t i n cl u d e s a t h i rd ( g r o u n d i ng ) p i n.
20 OOR LIMITS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 6 The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head.
21 UNLOCK DOOR LOCK TO REC ONNECT PULL TOW ARD DOOR TO RELEASE PULL TOW ARD THE OPENER FIG . 6-3 Engage/Disengage Carriage Lock . CARRIAGE LOCK The Carriage Lock can be manually engaged or disengaged. • T o disengage Carriage Lock – Pull handle downward opener power head .
22 FIG . 6-6 2 x 4 under center of door opening. CONT ACT REVERSE TEST The force adjustment s and limit switch settings MUST BE COMPLETED before testing. 1. T esting . • Open garage door using W all Control. – Place a 2" x 4" board (laid flat) under center of garage door opening (FIG .
23 FCC and IC CERTIFIED FIG . 7-1 Learn code button and LED SET SET OPEN FORCE CL OSE C ODE LEARN LIMIT M A N U AL Open T ravel Limit Open Set Limit Button Close T ravel Limit Close Set Limit Button D.
EMOTE CONTROL BA TTERY REPLACEM ENT AND VISOR CLIP INST ALLA TION 8 FIG . 8-1 Open battery cover . 1. Battery replacement . • T o open, gently push straight out on battery cover lock tab as shown. (Fig. 8-1) . • Slide open battery cover . – Remove old battery .
25 Use Wall Control supplied with opener . Any other Wall Control can cause the opener to operate unexpectedly . W ARNING If you have any questions, please do not hesitate to contact Genie ® customer service at: 1.800.354.3643 I M P O R T A N T S A F E T Y I N S T R U C T I O N S 1.
26 CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 2 3 4 1 2 3 1 2 POWER CORD CORDON DE SECTEUR CABLE ELÉCTRICO TERMINAL BLOCK BORNE BLOQUE DE TERMINALES WHITE BLANC BLANC.
27 TROUBLESHOOTING GUIDE - OPERA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM PROBLEM WHA T TO DO Opener does NOT run from W all Console. • Check power source. – P l u g a l am p i n to o u t l et u s e d f o r p ow e r h ea d . I f l am p w or k s , po w e r so u r c e i s OK.
TROUBLESHOOTING GUIDE - POWER HEAD LED FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM Power head LED Possible Problem Solution Red LED showing Green LED showing OFF OFF Normal operation None requi.
29 T ransmitters comply with all United St ates and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requiremen ts of any other jurisdiction.
An important point after buying a device Genie 2022 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Genie 2022 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Genie 2022 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Genie 2022 you will learn all the available features of the product, as well as information on its operation. The information that you get Genie 2022 will certainly help you make a decision on the purchase.
If you already are a holder of Genie 2022, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Genie 2022.
However, one of the most important roles played by the user manual is to help in solving problems with Genie 2022. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Genie 2022 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
