Instruction/ maintenance manual of the product 1000 Genie
Go to page of 14
SilentMax ™ 1000 Includes INTELLICODE ® 2 Remote Control. Safe-T-Beam ® System must be installed to close door. For use only with residential sectional or one piece overhead garage doors. Homelink ® and Car2U ® compatible. For Answers and Assistance: 1.
THIS P AGE LEFT BLANK.
T ABLE OF C ONTENTS Section .............................................................. Page Safety Information 2 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFET Y FEA TURES Safe-T-Beam® (STB) Non-Contact Reversing S ystem Puts an in visible beam across the door opening. The door stops and reverses to the full open position if anything th passes rough the beam. LED indicator lights on the powerhead and on the STBs p rovide a self diagnostic code if an operational problem exists.
4 ©2011 The Genie Company 9/2011 SET PROGRAM Open Tr a v e l ROUND LED Indicator F acing Garage Door Close Tr av e l Button O VERVIEW OF PO WERHEAD C ONTROLS This section describes the simple programming functions. Use this page to familiarize yourself with the buttons and LED indicators used to program the opener .
©2011 The Genie Company 9/2011 5 W ARNING s Make sure door way is in view and clear of obstacles and people to a void injury or damage to proper ty . s DO NOT operat e this unit from wall console before LIMITS and FORCE a re set. Severe damage to the opener can occur.
©2011 The Genie Company 9/2011 6 PROGRAMMING REMOTES to New Intellicode® 2 Openers. All type remotes program in the same way. Bring remote(s) to powerhead location. For Car2U® and HomeLink®, park car outside the garage with the ignition key in the “ACCESSORY” position.
7 ©2011 The Genie Company 9/2011 IntelliCode® 1 or 2 wireless keypad Door moves. (To verify memory is cleared—try to operate the garage door using one of your remote devices. The opener should not respond.) Both LEDs OFF confirms communication is established with operator .
8 ©2011 The Genie Company 9/2011 s With the door closed , pull release handle DOWN and let go to release door carriage assembly f rom drive system. s R s Raise and lower the door manually—it should move freely and smoothly. ’d n a t e e f 4 o t 3 y l e t a m i x o r p p a y l l a u n a m r o o d e s i a let go.
9 ©2011 The Genie Company 9/2011 CORRECTIVE MAINTENANCE TO ENGAGE , PULL DOWN AND TOWARD POWERHEAD . CHECK THE RED BLOCK IS IN THE UP POSITION. THEN LET GO. TO DISENGAGE , PULL DOWN AND TOWARD DOOR . CHECK RED BLOCK IN THE DOWN POSITION. THEN LET GO.
©2011 The Genie Company 9/2011 10 ADJUSTMENT GUIDE - FORCE SETTINGS F orce settings are pre-programmed at the factory and "learned" during the Open/Close Limit settings steps. For normal use, these settings should not need adjustment with this unit.
11 ©2011 The Genie Company 9/2011 REFERENCE - CIRCUIT WIRING DIA GRAM FOR HELP-1-800-35-GENIE OR WWW .GENIECOMP ANY .COM Opener circuit wiring diagram. This wiring diagram is for reference only . Opening C over Ma y Cause Electric Shock. Disconnect pow er from opener prior to remo ving cov er .
Opener does NO T run from wall console . s Check power source , – Plug a lamp into outlet used for powerhead . If lamp works, power source is OK. – If not, check fuse or circuit breaker . s If power is OK, – Check connections at powerhead terminals and at wall console.
13 ©2011 The Genie Company 9/2011 TROUBLESHOO TING GUIDE - POWERHEAD LEDs FOR HELP-1-800-35-GENIE OR WWW .GENIECOMP ANY .C OM P owerhead LED P ossible Problem Solution Round LED Long LED OFF OFF Norm.
An important point after buying a device Genie 1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Genie 1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Genie 1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Genie 1000 you will learn all the available features of the product, as well as information on its operation. The information that you get Genie 1000 will certainly help you make a decision on the purchase.
If you already are a holder of Genie 1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Genie 1000.
However, one of the most important roles played by the user manual is to help in solving problems with Genie 1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Genie 1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
