Instruction/ maintenance manual of the product EXT-HDMI1.3-CAT5-ELR Gefen
Go to page of 19
® Extender for HDMI ® 1.3 over CAT5 with Ethernet EXT-HDMI1.3-CAT5-ELR User Manual.
ASKING FOR ASSIST ANCE Rev A10 29.6 T echnical Support : T elephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 T echnical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday , Paci fi c Time Write T o: Gefen, LLC. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 9131 1 www .
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Unit Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 Connecting the Extender for HDMI 1.
1 Congratulations on your purchase of the Extender for HDMI 1.3 over CA T5 with Ethernet. Y our complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
READ THESE NOTES BEFORE INST ALLING OR OPERA TING THE EXTENDER FOR HDMI 1.3 OVER CA T5 WITH ETHERNET • The Extender for HDMI 1.3 over CA T5 with Ethernet units are housed in a metal box for better RF shielding. • CA T -5 cables should not exceed 330 feet.
3 HDMI 1.3 Features • 225 MHz (up to 12-bit YUV 444 @ 1080p) • Deep Color • Dolby T rueHD and DTS-HD Master Audio • Lip-Sync • CEC Pass-Through Features • Extends HDMI1.
4 SENDER UNIT LA YOUT Back Front 1 23 45 6.
5 SENDER UNIT DESCRIPTIONS 1 5V DC Locking Power Connector Connect the included 5V DC locking power supply to this connector . Only use the power supply shipped with this unit.
6 RECEIVER UNIT LA YOUT Front Back 1 2 3 4 5 67.
7 RECEIVER UNIT DESCRIPTIONS 1 IR Sensor Receives signals from the Hi-Def source IR remote control. The IR signals are sent back to the source device, when using an IR Blaster on the Sender . 2 Locking HDMI Port Connect a Hi-Def source device to this HDMI port.
8 1. Connect the Hi-Def source to the Sender Unit using the included HDMI cable. 2. Use an HDMI cable to connect the HDTV display to the Receiver Unit. 3. Connect the Ethernet device/router to the Ethernet input port on the Sender unit using a CA T -5, CA T -5e or CA T -6 cable.
9 DIP SWITCHES DIP Switch Location On the bottom of the Extender for HDMI 1.3 with Ethernet Receiver unit there are four (4) DIP switches. The DIP switches allow advanced EDID management of the Extender for HDMI 1.3 with Ethernet which may be necessary when troubleshooting or using different brands of hardware.
10 DIP SWITCH SETTINGS DIP 1 - EDID Mode ON (default) - External EDID Mode • DDC and HPD are passed through. Both the connection status and the full A/V capabilities of the display . The HPD status will also be detected by the source device. OFF - Internal EDID Mode • Local EDID is used instead of the EDID from the display device.
11 NETWORK CABLE WIRING DIAGRAM 12345678 Gefen recommends the TIA/EIA-568-B wiring option. Please adhere to the table below when fi eld terminating cable for use with Gefen products.
12 MOUNTING PLA TE INST ALLA TION 1 2 3 R emove the rubber feet covering the screws off the bottom of the unit. R emove the screws. Line up the mounting plates and screw it on to the unit.
TERMINOLOGY CA T -5/CA T5e Category 5 cable, commonly known as Cat 5, is an unshielded twisted pair type cable designed for high signal integrity . The actual standard de fi nes speci fi c electrical properties of the wire, but it is mostly known as being rated for its Ethernet capability of 100 Mbit/s.
12 Video Ampli fi er Bandwidth ....................................................................... 225 MHz Input Video Signal .............................................................................. 1.2 V olts p-p Input DDC Signal .........
13.
Rev A10 29.6 Pb 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com.
An important point after buying a device Gefen EXT-HDMI1.3-CAT5-ELR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Gefen EXT-HDMI1.3-CAT5-ELR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Gefen EXT-HDMI1.3-CAT5-ELR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Gefen EXT-HDMI1.3-CAT5-ELR you will learn all the available features of the product, as well as information on its operation. The information that you get Gefen EXT-HDMI1.3-CAT5-ELR will certainly help you make a decision on the purchase.
If you already are a holder of Gefen EXT-HDMI1.3-CAT5-ELR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Gefen EXT-HDMI1.3-CAT5-ELR.
However, one of the most important roles played by the user manual is to help in solving problems with Gefen EXT-HDMI1.3-CAT5-ELR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Gefen EXT-HDMI1.3-CAT5-ELR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
