Instruction/ maintenance manual of the product EXT-DVI-1CAT6-GI Gefen
Go to page of 28
Audio Embedder 3GSDI EXT-DVI-1CAT6-GI User Manual DVI over 1 CAT6 w/ Galvanic Isolator Release A2 *Pr eferred.
ii 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions.
iii Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notied within two (2) years from the da.
iv T echnical S upport (818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday , Pacic T ime Fa x (818) 772-9120 Email support@gefen.com We b http://www .gefen.com Mailing Addr ess Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 9131 1 Pr oduct R egistr ation Register your product here: http://www .
v • Always connect a bonding wire between an approved safety ground and the grounding screw on the chassis. • Electromagnetic Interference This product is subject to the following two conditions: .
vi Features and Packing List Features • Compliant with Medical Standards EN60601-1 and EN60601-1-2, 3rd Edition • Extends DVI up to 132 feet (40 meters) over CA T -6a • Extends DVI up to 100 fee.
.
viii Table of Contents 1 Get ting St arted Introduction............................................................................................................ 2 Sender unit .........................................................................
.
.
DVI over 1 CAT6 w/ Galvanic Isolator 1 Ge t ting St ar t ed Introduction............................................................................................................ 2 Sender unit ........................................................
page | 2 Page Title Introduction Sender unit DVI over 1 CAT6 w/ Galvanic Isolator S 5V DC Power DVI In Link EXT -DVI-1CAT6-GIS Gefen DVI over 1 CAT6 w/ Galvanic Isolator S 5V DC Power DVI In Link EXT .
page | 3 Page Title Introduction ID Name Description 1 Link Connect a CA T -5e cable (or better) from this port to the Link port on the Receiver unit. 2 5V DC Connect the included 5V DC power supply to this power receptacle.
page | 4 Page Title Introduction Getting S tart ed Getting S tart ed Receiver unit DVI over 1 CAT6 w/ Galvanic Isolator R 5V DC Power DVI Out EQ Link EXT -DVI-1CAT6-GIR Gefen 1 2 3 4 5 6 7 0 DVI over .
page | 5 Page Title Introduction Getting S tart ed ID Name Description 1 Link Connect a CA T -5e cable (or better) from this port to the Link port on the Sender unit.
page | 6 Connection Instructions 1. Connect the included DVI cable from the imaging source (e.g. camera) to the DVI In port on the Sender unit. 2. Connect a DVI cable from the DVI Out port, on the Receiver unit, to a video scaler or high-resolution imaging display .
.
.
DVI over 1 CAT6 w/ Galvanic Isolator 2 Basic Oper ation DIP Switch Conguration .................................................................................... 10 Default Settings ................................................................
page | 10 DIP Switch Conguration Basic Oper ation Basic Oper ation On the bottom panel of the Sender unit is a bank of 4 DIP switches. Remove the piece of colored tape to reveal the DIP switch bank. These DIP switches provide control over EDID management and color depth.
page | 1 1 EDID Management The DVI over 1 CA T6 w/ Galvanic Isolator can be switched between two EDID modes: Internal or Pass-through. After changing DIP switch 1, the Sender unit must be power-cycled for changes to take effect. DIP Switch 1 Description ON (default) Pass-through mode.
page | 12 The Receiver unit of the DVI over 1 CA T6 w/ Galvanic Isolator has a trim pot that is used to equalize the output signal, compensating for extension distance and cable skew . If there is no output video or if output video contains video artifacts and/or video noise such as snow , use the steps below to adjust the trim pot.
.
.
DVI over 1 CAT6 w/ Galvanic Isolator 3 Appendix Surface Mounting Instructions ............................................................................. 16 Specications ............................................................................
page | 16 The Sender and Receiver units can be mounted on any at surface, as shown below (screws not included). There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the DVI cables.
page | 17 Specications Appendix Connectors & Indicators Video Input (Sender) • 1 x DVI 29-pin, female (digital only) Video Output (Receiver) • 1 x DVI 29-pin, female (digital only) Link (Se.
20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.
An important point after buying a device Gefen EXT-DVI-1CAT6-GI (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Gefen EXT-DVI-1CAT6-GI yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Gefen EXT-DVI-1CAT6-GI - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Gefen EXT-DVI-1CAT6-GI you will learn all the available features of the product, as well as information on its operation. The information that you get Gefen EXT-DVI-1CAT6-GI will certainly help you make a decision on the purchase.
If you already are a holder of Gefen EXT-DVI-1CAT6-GI, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Gefen EXT-DVI-1CAT6-GI.
However, one of the most important roles played by the user manual is to help in solving problems with Gefen EXT-DVI-1CAT6-GI. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Gefen EXT-DVI-1CAT6-GI along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
