Instruction/ maintenance manual of the product ZET2 GE
Go to page of 16
1 30 ” Built-In W all Oven Installation Instructions ZET1, ZET2 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before Y ou Begin Read these instructions carefully and completely . • IMPORT ANT —Save these instructions for local inspector ’ s use.
2 IMPORT ANT SAFETY INSTRUCTIONS Installation Instructions For Y our Safety • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
3 Open oven door and remove literature pack, broiler pan and grid, oven racks, rack supports and a bag with 9 hex nuts. Read Installation Instructions carefully before you begin. Be sure to place all literature, Owner ’s Manual, Installations, etc. in a safe place for future reference.
4 Place the oven on a table or platform even with the cutout opening. (Platform must support 175 lbs. [79 kg] single, 350 lbs. [159 kg] double.) Installation Instructions Pre-Installation Checklist cont. Remove the bottom trim from the top of the oven.
5 Cabinet Width 30 ” (76.2 cm) Recommended Minimum Cutout Location from Floor 32 1/2 ” (82.6 cm) Cutout Depth 23 1/2 ” (59.7 cm) Min. Cutout Width 28 1/2 ” (72.4 cm) Min. 28 5/8 ” (72.7 cm) Max. Cutout Height 27 1/4 ” (69.2 cm) Min. 27 5/16 ” (69.
6 Installation Instructions Cabinet Width 30 ” (76.2 cm) Recommended Minimum Cutout Location from Floor 12 ” (30.5 cm) Cutout Depth 23 1/2 ” (59.7 cm) Min. Cutout Width 28 1/2 ” (72.4 cm) Min. 28 5/8 ” (72.7 cm) Max. Cutout Height 51 13/16 ” (131.
7 Installation Instructions Cutout for Single Built-In Oven Under Counter A3 25" Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.
8 Cabinetry NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the W arming Drawer location do not obstruct the required interior 23 1/2 ” (59.7 cm) depth and 9 1/4 ” (23.5 cm) height. • These Monogram Ovens require 3/4 ” (1.
9 NOTE: The middle rail separating the two openings may need to be larger than the 2 ” (5.1 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.
10 (Continued on following page) Installation Instructions Electrical Connections ATTENTION INST ALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit.
11 Installation Instructions Electrical Connections cont. B6 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
12 (Continued on following page) W ARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet causing serious injury . Installation Instructions Securing the Oven in the Opening Drilling the Pilot Holes and Mounting the Oven a.
13 Installation Instructions Installing the Metal Bottom T rim IMPORT ANT : If this unit is ever removed from the cabinet or the oven is ever pulled out for service, the trim must be removed first or damage to the trim will occur . C4 a. Place the bottom trim between the side trim and against the bottom of the cutout.
14 Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position, seat the notch of the hinge arm into the bottom edge of the hinge slot.
15 Installation Instructions Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. NOTE T O ELECTRICIAN: Y ou must unplug the green wire (near where the long flexible conduit exits the unit) when conducting high-potential testing.
16 Printed in U.S.A..
An important point after buying a device GE ZET2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE ZET2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE ZET2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE ZET2 you will learn all the available features of the product, as well as information on its operation. The information that you get GE ZET2 will certainly help you make a decision on the purchase.
If you already are a holder of GE ZET2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE ZET2.
However, one of the most important roles played by the user manual is to help in solving problems with GE ZET2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE ZET2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
