Instruction/ maintenance manual of the product PGP989 GE
Go to page of 8
Questions? Call 800. GE. CARES (800.432.2737) or Visit our Website at: ge. com LP Conversion Gas Cook t op Instructions Read these instructions completely and carefully. • IMP ORT ANT – Save these instructions for local inspector ’s use. • IMP ORT ANT – Obser ve all governing codes and ordinances.
CONVER T SURF ACE BURNERS First remove, convert and replace the left side sur face burners and then the right side surface burners. Remove the grates, burner caps and burner heads. Remove the screws securing the burner bases to the burners. Pull out the electrodes without removing the electrode leads.
CONVER T SURF ACE BURNERS (cont .) Replace the gaskets, burner bases and electrodes. Install the two screws in each burner base. Do not overtighten. The maximum torque is 10 inch pounds. Push the igniters all the way down into the burner head. Install the burner heads, burner caps and grates in their original burner positions.
4 AD JUST THE L OW FL AME (SIMMER) SE T TING The top burner valves have low flame/simmer adjustment screws in the center of the control shafts. A flashlight may be needed to locate the screw . A small, thin-blade screwdriver (approximately 1/8 ″ blade width) is needed to access the screw .
¿Preguntas? Llame al 800. GE. CARES (800.432.2737) o visite nuestro sitio Web en: ge.com Instrucciones de Estufa de gas conversión a gas LP Lea estas instrucciones por completo y con detenimient o. • IMP ORT ANTE – Guarde estas instrucciones para el uso de inspectores locales.
Instrucciones de conversión • Con la instalación de este kit de conversión, la estufa debe funcionar con gas LP a una presión de columna de agua de 10" . • El regulador de pr esión debe estar conectado en serie con el colector de la estufa y debe permanecer en serie con la línea suministro.
CONVERSIÓN DE QUEMADORES DE SUPERFICIE (cont .) Reemplace las juntas, bases de los quemadores y electrodos. Instale los dos tornillos en cada base de quemador . No ajuste de más. El torque máximo es de 10 libras por pulgada. Empuje los encendedores bien hacia abajo dentro del cabezal del quemador .
4 AJUSTE L A CONFIGURACIÓN DE LL AMA BAJA (FUEGO LENTO) Las válvulas de los quemadores superior es cuentan con tornillos de ajuste para llama baja/fuego lento en el centro de las barras de contr ol. Puede necesitarse una linterna para ubicar el tornillo.
An important point after buying a device GE PGP989 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE PGP989 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE PGP989 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE PGP989 you will learn all the available features of the product, as well as information on its operation. The information that you get GE PGP989 will certainly help you make a decision on the purchase.
If you already are a holder of GE PGP989, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE PGP989.
However, one of the most important roles played by the user manual is to help in solving problems with GE PGP989. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE PGP989 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
