Instruction/ maintenance manual of the product ZICS360N RH GE Monogram
Go to page of 20
Monogram. We bring good things to life. ® If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Installation Instr uctions ZIC360N RH, ZIC360N LH, ZICS360N RH, ZICS360N.
Safety Information Skill Level - Installation of this refrigerator requires basic mechanical, carpentr y and plumbing skills. Proper installation is the responsibility of the in- staller . Product failur e due to improper installation is not covered under the GE Appliance W ar ranty .
Design Guide THE INST ALLA TION SP ACE The finished cutout width must be 35-1/2". Water And Electrical Locations The opening must be prepared with the electrical and water supply located as shown. The cutout depth must be 24". Designed for industr y standard flush installation.
1/4" 1/2" 3/4" 1" 1-1/4" 1" 3/4" Overlay Panel (Nominal Size) 1/4" 1/2" 3/4" 2" 1-1/4" 1-1/2" 1-3/4" 3" 2-1/4" 2-1/2&quo.
1/4" 1/2" 3/4" 1" 1-1/4" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Overlay Panel (Nominal Size) Case T rim.
Design Guide CUSTOMIZA TION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Overlay panels Y ou may also choose to install custom overlay panels from your cabinet manufacturer . This design provides a seamless appearance which integrates smoothly with sur rounding cabinetr y .
Design Guide 1/4" FRAMED P ANEL DIMENSIONS 7 If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door , drawer and grille.
Design Guide 8 SIDE P ANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim.
Installation Instructions 9 MA TERIALS REQUIRED • 35" long 2x4 for Anti-Tip support • Copper water line tubing • W ater shut-off valve (optional but recommended) • Custom panels for fresh food door , freezer drawer and grille panel • Screws to secure refrigerator to cabinetr y .
Installation Instructions NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber . STEP 1 REMOVE P ACKAGING CAUTION: Refrigerator is much heavier at the top than at the bottom – be careful when moving.
Installation Instructions 11 STEP 2A W A TER LINE INST ALLA TION WITH A REVERSE OSMOSIS SYSTEM Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis W ater System use the refrigerator’s filter bypass plug.
12 Installation Instructions STEP 5 LEVEL REFRIGERA TOR All models have 4-point leveling. The front is sup- ported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator . • T o level the back of the refrigerator , turn the 7 /1 6" hex nut located above the front wheels.
STEP 7 ADJUST DOOR SWING NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130 ° , you may change the door swing to a 90 ° opening. Skip this step if door opening is satisfactor y for your installation situation.
Installation Instructions 14 STEP 9 INST ALL FRAMED P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes.
Installation Instructions 15 STEP 9A INST ALL OVERLA Y P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the REAR screw holes. • Secure the handle to the door using the FRONT screw holes.
16 Installation Instructions STEP 1 0 CONNECT W A TER SUPPL Y Check to be sure that refrigerator power cord is not plugged into the wall outlet. • Locate and bring copper tubing to the front of the cabinet. • T ur n the water on to flush debris from line.
17 Notes.
18 Notes.
19 Notes.
Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram TM local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
An important point after buying a device GE Monogram ZICS360N RH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE Monogram ZICS360N RH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE Monogram ZICS360N RH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE Monogram ZICS360N RH you will learn all the available features of the product, as well as information on its operation. The information that you get GE Monogram ZICS360N RH will certainly help you make a decision on the purchase.
If you already are a holder of GE Monogram ZICS360N RH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE Monogram ZICS360N RH.
However, one of the most important roles played by the user manual is to help in solving problems with GE Monogram ZICS360N RH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE Monogram ZICS360N RH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
