Instruction/ maintenance manual of the product JTP20 GE
Go to page of 16
1 30 ” Built-In W all Oven Installation Instructions JTP20, JTP25, JTP28, JTP48, JTP50, JT912, JT915, JT952, JT955, ZET938, ZET958 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before Y ou Begin Read these instructions carefully and completely .
2 Electrical Requirements This appliance must be supplied with the proper voltage and frequency , and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating plate is located on oven frame.
3 Open oven door and remove literature pack, broiler pan and grid, and oven racks. Remove Installation Instructions from literature pack and read them carefully before you begin. Be sure to place all literature, Owner ’s Manual, Installations, etc. in a safe place for future reference.
4 Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. single, 275 lbs. double.) Installation Instructions Pre-Installation Checklist cont. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process.
5 Cabinet Width 30 ” Recommended Minimum Cutout Location from Floor 32 1/2 ” Cutout Depth 23 1/2 ” Min. Cutout Width 28 1/2 ” Min. 28 5/8 ” Max.
6 Installation Instructions Cabinet Width 30 ” Recommended Minimum Cutout Location from Floor 12 ” Cutout Depth 23 1/2 ” Min. Cutout Width 28 1/2 ” Min.
7 Installation Instructions Cutout for Single Built-In Oven Under Counter NOTE: This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop. A3 25" Gas or electric cooktops may be installed over this oven.
8 (Continued on following page) Installation Instructions Electrical Connections ATTENTION INST ALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit.
9 Installation Instructions Electrical Connections cont. B4 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
10 (Continued on following page) W ARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet causing serious injury . Installation Instructions Securing the Oven in the Opening Drilling the Pilot Holes and Mounting the Oven a.
11 a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center of each template mark.
12 Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position (half way between the closed and broil stop position, seat the notch of the hinge arm into the bottom edge of the hinge slot.
13 Installation Instructions Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Pre-T est Checklist Check that the bottom trim is installed properly (see page 1 1).
14 NOTES.
15 NOTES.
16 NOTES.
An important point after buying a device GE JTP20 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE JTP20 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE JTP20 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE JTP20 you will learn all the available features of the product, as well as information on its operation. The information that you get GE JTP20 will certainly help you make a decision on the purchase.
If you already are a holder of GE JTP20, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE JTP20.
However, one of the most important roles played by the user manual is to help in solving problems with GE JTP20. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE JTP20 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
