Instruction/ maintenance manual of the product JKS05 GE
Go to page of 12
Before you begin Read these instructions carefully and completely • IMPORT ANT -Save these instructions for local inspector ’ s use. • IMPORT ANT -Observe all governing codes and ordinances. • Note to Installer- Be sure to leave these instructions with the consumer .
• Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury .
Installation Instructions EASY INSTALLATION OF YOU NEW 30" WALL OVEN Before you begin-Read these instructions completely and carefully. IMPORTANT- Save these instructions for local inspector's use. IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Pre- Installation Checklist cont. Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. single, 275 lbs. double.) 4 Remove the bottom trim from the top of the oven. It will be installed at the end of installation.
5 Cutouts for Single Built-In-Oven A1 Installation Instructions Cabinet Wid t h 27 Recommended Cutout Location from Floor 32 1/2” Cutout Depth 23 1/2” Cutout Wid t h 25” Min.
NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” thick, shim both sides equally to establish the cutout width. Cutouts for Double Built-In-Oven A2 6 Cabinet Wid t h 27” Recommended Cutout Location from Floor 13 1/4” Cutout Depth 23 5/8” Min.
NOTE: This Oven is not approved to be installed under a Solid Disk, Induction or Downdraft Modular Cooktop. Cutout s for Single Oven Under Counter A3 Installation Instructions 7 25" Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size.
8 T urn off the circuit breaker or remove fuses to the oven branch circuit. With the oven in front of the cabinet opening, on a table or platform, connect the flexible conduit to the electrical junction box as shown below . Y ou will need to purchase a strain relief clamp to complete the connection of the conduit to the junction box.
OR Three-Conductor Branch Circuit Connection When connecting to a 3-conductor branch circuit, if local codes permit: Junction Box Cover a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using wire nut.
b. Lift oven into cabinet cutout using the oven opening as an grip. Carefully push against oven front frame. Do not push against outside edges. c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop.
D1 D2 D3 D4 D5 The oven door is heavy . Y ou may need help lifting the door high enough to slide it into the hinges slots. Do not lift the door by the handle. 11 Replacing the Oven Door D Inst allation Instructions Pick the Oven Door up by placing one hand on each side.
12 Installation Instructions Pub. No. 31-10473 229C 4053P452 PRE-TEST CHECK LIST E Remove all protective film if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 10).
An important point after buying a device GE JKS05 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought GE JKS05 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data GE JKS05 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, GE JKS05 you will learn all the available features of the product, as well as information on its operation. The information that you get GE JKS05 will certainly help you make a decision on the purchase.
If you already are a holder of GE JKS05, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime GE JKS05.
However, one of the most important roles played by the user manual is to help in solving problems with GE JKS05. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device GE JKS05 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
