Instruction/ maintenance manual of the product 174 Garmin
Go to page of 30
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 1 GPS 150 INST ALLA TION MANUAL GARMIN INTERNATIONAL, INC. PART NUMBER: 190-00026-00 1200 E. 151st STREET REVISION Q, 3 APRIL 1998 OLATHE, KANSAS 66062.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 2 © Copyright 1992-1998 Garmin Corporation All Rights Reserved This publication is the proprietary property of Garmin International Inc. It may not be reproduced or transmitted in any form whether printed or electronic, without the expressed written consent of Garmin International.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 3 T ABLE OF CONTENTS SECTION 1 GENERAL DESCRIPTION 1 . 1 INTRODUCTION 1 . 2 TECHNICAL CHARACTERISTICS 1.2.1 PHYSICAL CHARACTERISTICS 1.2.2 O P E R A T I ONAL CHARACTERISTICS 1.2.3 INTERFACES SECTION 2 INSTALLATION CONSIDERATIONS 2 .
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 4 LIST OF ILLUSTRA TIONS FIGURE 1 - 1 PINOUT DEFINITION 1 - 2 INTERCONNECT SCHEMATIC 2 - 1 ANTENNA INSTALLATION CONSIDERATIONS 2 - 2 GPS INSTALLATION C.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 5 SECTION 1 GENERAL DESCRIPTION 1.1 INTRODUCTION This manual describes the physical, mechanical, and electrical characteristics and the installation requirements for the GPS 150 Aviation Kit.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 6 Nav Flag: Capable of driving up to three 1000 ohm parallel (Pins 3 and 4) loads, 375 millivolts for flag out-of-view, and +40 millivolts for flag in-view. OBI data: Output providing bearing to waypoint data for a (Pins 7, 8, and 23) Bendix/King RMI (KI 229 or equivalent).
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 7 SECTION 2 INST ALLA TION CONSIDERA TIONS Careful planning and consideration of the suggestions in this section are required to achieve the desired performance and reliability from the GPS 150. 2.1 ANTENNA CONSIDERATIONS 2.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 8 2 ) Replace or clean VHF COMM rack connector to assure good coax ground. 3 ) Place a grounding brace between the GPS 150, VHF COMM, and ground. 4 ) Shield the VHF COMM wiring harness. 2.2 RACK CONSIDERATIONS 2.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 9 SECTION 3 INST ALLA TION PROCEDURE 3 . 1 INSTALLATION ACCESSORIES The following installation accessories are available: ANTENNA AND RACK OPTIONS 010-.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 10 with sealant. Insure that the mounting screws are fully tightened and that the antenna base is well seated against the gasket. CAUTION: Do not use construction grade RTV sealant or sealants containing acetic acid.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 11 3 . 4 RACK INSTALLATION A. Figure 3-4 shows outline dimensions for the aviation rack. Install the rack in a rectangular 6.320" x 2.000" hole in the instrument panel. Exercise caution when installing the rack into the instrument panel.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 12 With power applied to the aviation rack and the GPS 150 unit off, continuously depress the ENT key and turn the unit on (release the ENT key when the display activates). Rotate the outer knob, and the CDI Test Page will be displayed.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 13 Arrival O F F Ensure the Arrival Annunciator is OFF O N Ensure the Arrival Annunciator is ON Select the Power Test Page by removing the cursor from the Annunciator Test Page and turning the outer knob one detent to the right.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 14 FIGURE 1-1 PINOUT DEFINITION.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 15 FIGURE 1-2 INTERCONNECT SCHEMATIC.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 16 Maintain 6"(16 cm) compass safe distance FIG 2-2 GPS INSTALLATION CONSIDERATIONS FIG 2-1 ANTENNA INSTALLATION CONSIDERATIONS A ntenna masked by vertical fin, T tail, or dorsal fin A ntenna must be on top of aircraft.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 17 FIG 3-1 STUD MOUNT GA 56 ANTENNA INSTALLATION.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 18 FIGURE 3-2 FLANGE MOUNT GA 56 ANTENNA INSTALLATION.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 19 FIGURE 3-3 COAX CABLE INSTALLATION.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 20 FIGURE 3-4 AVIATION RACK DIMENSIONS.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 21 FIGURE 3-5 AVIATION RACK INSTALLATION.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 22 APPENDIX A INST ALLA TION DET AILS FOR BEECH V35B 1 . 0 INTRODUCTION This appendix provides airframe specific information which is necessary to install the GARMIN GPS 150 navigation system in the Beech Bonanza Model V35B in accordance with STC SA00066WI.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 23 2 . 4 PLACARDS After completion of the GPS 150 system installation, affix a durable placard on the instrument panel in the location shown in Figure A-3 which states “GPS limited to VFR use only".
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 24 FIG A-1 FUNCTIONAL BLOCK DIAGRAM.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 25 FIG A-2 FUSELAGE STATIONS AND WEIGHT AND BALANCE DATA.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 26 FIG A-3 PANEL LAYOUT AND BREAKER LOCATION.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 27 FIG A-4 WIRING DIAGRAM.
APPENDIX B CONNECTOR CHANGES STAMPED CONTACT CONNECTOR USAGE Garmin panel mount GPS radios have previously been shipped with stamped crimp type contacts.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 29 APPENDIX C STC PERMISSION Consistent with N8110.69 or Order 8110.4, Aviation Authority approved installers are hereby granted permission to use STC# SA00066WI data to modify aircraft.
Av. Kit Install. Manual 190-00026-00 Rev. Q Page 30.
An important point after buying a device Garmin 174 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Garmin 174 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Garmin 174 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Garmin 174 you will learn all the available features of the product, as well as information on its operation. The information that you get Garmin 174 will certainly help you make a decision on the purchase.
If you already are a holder of Garmin 174, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Garmin 174.
However, one of the most important roles played by the user manual is to help in solving problems with Garmin 174. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Garmin 174 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center