Instruction/ maintenance manual of the product TK 2400 ECO Güde
Go to page of 16
#55166 TK 2400 ECO © Güde GmbH & Co. KG - Birkichstrasse 6 - D-74549 Wolper tshausen - Deutschland English GB 18 Translation of original operating instructions Circular saw bench.
Unit Mobile bench circular saw with a quality aluminium stop and a plastic mitre cut stop, height r eadjustment and mitre adjustmen t b y a hand wheel.
Guarantee The guarantee exclusively applies to material or manufacturing defects. The original proof of purch ase with the purchase date m ust be submitted when lodging a claim in the guaran tee period. The guara ntee does not include any unauthorised use, e.
Product Safet y Product compliance with respective EU standards Bans: General ban In combination with another pictogram) Do not touch rotating parts Warning: Warning/caution Beware of hazardous electr.
The manufacturer shall not be made liable for damages if general rules and this manual regulations are not observed. Residual Hazards and Protecti ve Action Mechanical Residual Hazards Hazard Descript.
Operator Requiremen ts The operator shall read the instruction manual carefully before using the unit. Qualification No special qualification is required for use of the unit except for d eta iled direction by a professional. Minimum Age Only persons above 16 years of age are allowed to work with the unit.
+ Fig. 4 Structural group 4 Required structural groups Delivered parts and accessories Structural group 3 Fig. 1 – pos . 8/8 x Fig. 1 – pos. 9/8 x Fig.
Fig. 5 Structural group 5 Required structural groups Delivered parts and accessories Fig. 6 Structural group 4 Fig. 1 – pos. 12 Fig. 1 – pos. 14 Fig. 1 – pos. 13 Fig. 1 – pos. 15 Initial Operation Safet y Instruction • Unplug the unit before any adjustment and maintenance .
• Use only perfect saw discs. I.e. sharpened, without any cracks, fissures, deformations etc. Faulty discs have to be replaced immediately. • Be particular about the arrow on the disc pointi ng on the same dire ction as that on the unit. . • The unit protection devices ma y never be removed or removed from operation in a ny way.
Mitre cut stop Fig. 8 • Put the mitre cut stop (Fig. 2/pos. 14) in the respective clamp on the bench. • Release the mitre cut stop (Fig. 2/pos. 14) with the knurled screw .
Lengthwise Cut ting Fig. 12 • Set the parallel stop (Fig. 2/pos. 3) at the required width in relation to the saw disc. . • Lay the work on the bearing surface are, the flatter/wider side should lay flat on the saw bench. • Guide the wider work with hand, the smaller one with use of a sliding guide rod (Fig.
Splitting w edge set-up Fig. 15 • Remove the saw disc cover (Fig. 2/pos. 1). • Remove the removable part of the bench and loosen both the screws on the bench area . • Loosen the screw on the wedge so that the wedge may be shifted – see the type of cut at issue .
Fig. 18 Inspections and Mainte nance Unplug the unit before any works on it. • Use a damp cloth to clean plastic parts. Do not use detergents, solvents and pointed things either. • Clean any dirt from the bench surface with a suitable curing compound spra y.
Fig. 22 • Put wrench 13 on the disc spindle . Fig. 23 • Take the belt from the pulley using the screwdriver while turning the disc spindle in the direction of the small pulley. Fig. 24 • Turn until the belt is completely taken off the small pulley .
Fig. 29 • Finished! The saw is in working order again . Inspection and Mainte nance Safety Instructi ons Only a unit maintained and cared for on a regular basis may be a serviceable aid. Insufficient maintenance and care m ay result in emergencies and unforeseen accidents.
EC Declaration of Conformity We herewith declare Güde GmbH & Co. KG Birkichstraße 6, 74549 Wolpertshaus en, Germany That the follo w ing Appliance complies with the appropriate basic safety and health requirements of the EC Directiv e based on its design and type, as brought into circulation by us.
An important point after buying a device Güde TK 2400 ECO (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Güde TK 2400 ECO yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Güde TK 2400 ECO - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Güde TK 2400 ECO you will learn all the available features of the product, as well as information on its operation. The information that you get Güde TK 2400 ECO will certainly help you make a decision on the purchase.
If you already are a holder of Güde TK 2400 ECO, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Güde TK 2400 ECO.
However, one of the most important roles played by the user manual is to help in solving problems with Güde TK 2400 ECO. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Güde TK 2400 ECO along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
